(e)
Tighten the potable-water tube connection (46).
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES AND A MASK.
R EFF : 001-049, 051-099, 101-105, 151-199, 25-41-41Page 441 201-210, 213-299, Config-2 Aug 01/05
CES
(f)
Apply the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-010) to the seals (48).
(g)
Put the protective tubing (47) in position on the seals (48).
(h)
Open the sanitary cabinet door (41).
(i)
Remove the blanking plugs and put the potable-water tube assembly
(42) in position. Install and tighten the connections (43) and (44).
(j)
Close the sanitary cabinet door (41). WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING AND RUBBER GLOVES.
(k)
Apply the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) to the ends of the sleeve (51).
(6) Connect the electrical connector R (Ref. Fig. 405/TASK 25-41-41-991-017)
(a)
Remove the blanking caps from the electrical connectors.
(b)
Make sure that the electrical connectors are clean and in the correct condition.
(c)
Connect the electrical connector 7200VC-A (2).
(d)
Install the access flap (1) on the rear wall (3). WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(e)
Apply the SPECIAL MATERIALS (Material No. 05-002) to the door step attach screws (7).
(f)
Put the door step (8) in position and install the screws (7).
(g)
Torque the screws to between 0.37 and 0.42 m.daN (32.74 and 37.16 lbf.in).
R EFF : 001-049, 051-099, 101-105, 151-199, 25-41-41Page 442 201-210, 213-299, Config-2 Aug 01/05
CES
(h)
Apply the sealant. WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(i)
Apply the SEALANTS (Material No. 09-016) to the floor pan and the floor panel at the lavatory door opening.
(7)
Connect the toilet drain-line behind the lavatory (Ref. TASK 38-30-00-410-002).
(8)
Install the toilet assembly (Ref. TASK 38-31-41-400-001). Do not install the toilet shroud at this time.
(9) Install the programming and test panel (Ref. TASK 23-73-18-400-001). R **ON A/C 106-149, 301-399, 401-499,
Subtask 25-41-41-420-059-D
D. Installation of Lavatory A
(1)
Assemble the lavatory. R (Ref. Fig. 409/TASK 25-41-41-991-022)
(a)
Put the lavatory subassemblies (108) and (111) in the center of the aircraft aisle.
(b)
Put the subassemblies together and install the washers (109) and the screws (110).
(c)
Install the washers (107) and the screws (106).
(d)
Install the screw (104) and the cap (105).
(e)
Put the lavatory assembly in position on the floorpan (100).
(f)
Install the washers (102), the screws (101) and the screws (103).
(2)
Connect the electrical connections. R (Ref. Fig. 408/TASK 25-41-41-991-021)
(a) Remove the temporary attachment from the electrical cable assembly (84) and the junction box (90).
R EFF : 001-049, 051-099, 101-149, 151-199, 25-41-41Page 443 201-210, 213-299, 301-399, 401-499, Config-2 Aug 01/05
CES
(b)
Carefully put the cable assembly and the junction box through the cut out in the lavatory ceiling (81).
(c)
Put the junction box (90) in position on the lavatory rear side-wall (82) and install the washers (89) and the screws (88).
(d)
Attach the electrical cable assembly (84) to the mounts (92) on the lavatory side-wall (82) with the new cable ties (91).
(e)
Carefully put the electrical cable assembly (87) through the opening in the lavatory rear side-wall (82).
(f)
Remove the blanking caps and connect the electrical cable (87) to the micro switch (86).
(g)
Put the micro switch in position and install the screws (85).
(3) Install the upper and lower attachments. R (Ref. Fig. 407/TASK 25-41-41-991-020)
(a)
Apply the COMMON GREASE (Material No. 04-004A) to the bolts (67) and (69).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备3(78)
