-
The beeper stops.
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
25. On the oven: On the oven:
-Push the OFF pushbutton. - The displays and all of the indicators go off.
R **ON A/C 051-099, 151-199, 201-210,
Subtask 25-35-00-710-066-A
A. Do the Operational Test of the Oven
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the control module of the On the control module of the oven:
oven: - The ON/OFF indicator comes on.
- Push the ON/OFF pushbutton. - The MED indicator comes on.
- The HEATINGTIME display shows 00.
- The SERVINGTIME display shows 00.
- Turn the TIME SELECTOR knob to - The HEATINGTIME and the SERVINGTIME
set the heatingtime to 4 display show the adjusted time.
minutes.
- Push the HEATINGTIME SET - The HEATINGTIME SET indicator comes
pushbutton. on.
- Turn the TIME SELECTOR knob to - The SERVINGTIME display shows the
set the servingtime to 6 adjusted time.
minutes.
- Push the SERVINGTIME SET - The SERVINGTIME SET indicator comes
pushbutton. on.
- Push the TEMP pushbutton three - The HIGH, the LOW and the MED
times. indicator come on one after the
other.
- Push the START pushbutton. - The START indicator comes on and the
servingtime countdown starts.
R EFF : 001-049, 051-099, 101-105, 151-199, 25-35-00Page 512 201-210, May 01/05
CES
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
-
Wait until the SERVINGTIME and the HEATINGTIME display shows the same time.
-
Wait until the HEATINGTIME display shows 01 minutes and push the TEMP pushbutton.
-
Wait until the HEATINGTIME display shows 00 minutes.
-Push the ON/OFF pushbutton.
-
The operation cycle starts. You cansee this on the HEATINGTIME display.
At the oven:
-
The oven operates and the temperature in the oven will increase.
On the control module of the oven:
-Both displays show the inner oventemperature.
-A beeper gives a signal for 20seconds.
-The displays and all indicators go off.
R **ON A/C 106-149, 211-299, 301-399, 401-499,
Subtask 25-35-00-710-066
A. Do the Operational Test of the Oven
(1)
If installed, use the oven control panel to operate the oven.
(2)
Do step 1. only if an OUTLET is installed.
(3)
Do step 3. only if there is an arrow symbol on one of the oven fan-blades.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the oven:
-Put the OVEN/OFF/OUTLET switch
to the OUTLET position.
On the oven: At the electrical OUTLET of the oven:
-Measure the voltage at the - A voltage (115VAC) is on the OUTLET OUTLET or connect any and/or if connected the device can
R EFF : 051-099, 106-149, 151-199, 201-299, 25-35-00Page 513 301-399, 401-499, Aug 01/05
CES
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
applicable device to the OUTLET.
-Put the OVEN/OFF/OUTLET switch to the OVEN position.
2. On the oven:
-If installed, put the ON/OFF switch to the ON position.
3. On the oven:
-Do a check of the rotating field of the fan.
4. On the oven:
-
Set the temperature-switch to the low temperature.
-
Set the heater-time to max. 3 minutes.
-After the selected time:
5. On the oven:
-Do the step 2. again for each available temperature.
6. On the oven:
-Set the related switch to the OFF position.
operate.
On the oven:
-
The blower operates. A usual noisefrom the blower is heard. Any unusual noise is not permitted.
-
The indicator of the active temperature comes on.
- 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备3(43)
