WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME
_______ DAMAGED OR INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.
(a)
Apply COMMON GREASE (Material No. 04-004A) to the bushes (6).
(b)
Install the bushes (6) in the floor hardpoints.
(c)
Install the new packings (5).
(d)
Put the blocks (4) in position on the hardpoints.
(e)
Apply COMMON GREASE (Material No. 04-004A) to the threads of the bolts (8).
(f)
Install the bolts (8) and the washers (7).
(g)
Install the shims (3) on the blocks (4).
(h)
Carefully lift the galley and put it in position on the blocks
(4) and the shims (3).
(i)
Install the eccentric plugs (11) and the eccentric bushes (12). NOTE : If necessary, turn the eccentric plugs (11) and the
____ eccentric bushes (12) until the holes in the galley align with the holes in the blocks (4).
(j)
Install the plates (14) and the shims (13).
(k)
Apply COMMON GREASE (Material No. 04-004A) to the threads of the bolts (16).
(l)
Install the bolts (16) and the washers (15).
(m)
Put the covers (9) in position and install the screws (10).
(n)
Install the strips (1) and the screws (2).
(o)
Remove the temporary ties from the electrical connector (20).
(p)
Put the bracket (17) in position and install the electrical connector (20) and the screws (19).
(q)
Install the screws (18) and the bracket (17).
(2)
Install the Upper Attachments (Ref. Fig. 403B/TASK 25-31-41-991-018-A)
(a)
Put the brackets (11) in position and install the bolts (10), the washers (9) and the nuts (8).
(b)
Put the tie-rods (14) in position on the brackets (11) and install the bolts (8), the washers (6) and the nuts (13).
(c)
Put the tie-rods (14) in position on the aircraft structure and install the quick-release pins (5).
(d)
If necessary, remove and adjust the tie-rods (14). WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE LOCKWIRE.
_______
(e)
Install the panel (1) and the screws (2).
(f)
Put the pelmet (4) in position and install the screws (3).
(3)
Install the Air and Water Connections (Ref. Fig. 402B/TASK 25-31-41-991-014-A)
CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE
TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
1_ Remove and discard the lockwire.
2_ Loosen the locknut.
3_ Adjust the tie-rod end until the quick-release pins (5) can
easily be installed.
4_ Tighten the locknut.
5_ Make sure that the tie-rod end is in safety.
WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE_______
LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE AS
YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR BLIND
YOU.
6_ Saftey the locknut with MISCELLANEOUS (Material No. 19-010).
WARNING : MAKE SURE THAT THE POTABLE WATER SYSTEM IS DEPRESSURIZED. A
_______ PRESSURIZED SYSTEM CAN CAUSE INJURY TO PERSONS WHEN THEY DO WORK ON IT.
(a)
Remove the blanking plugs from the disconnected line ends.
(b)
Connect the potable water pipe (9) to the supply connection (7) and tighten the nut (8).
(c)
Connect the water drain pipe (4) to the water drain connection
(6) and install the clamps (5).
(d)
Connect the hose (15) to the hose (13) and tighten the clamps (14).
(e)
Connect the hose (12) to the hose (11) and tighten the clamp (10).
(4) Connect the Power Supply. (Ref. Fig. 401B/TASK 25-31-41-991-038-A)
CAUTION : REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN YOU
_______ CONNECT THE ELECTRICAL WIRES. IF YOU MAKE AN ERROR WHEN YOU CONNECT THE WIRES YOU WILL CAUSE DAMAGE TO EQUIPMENT.
(a)
Install the bolts (10), the washers (11) and the nuts (13) to connect the bonding straps (12) (Ref. TASK 20-28-00-912-004).
(b)
Put the clamps (1) in position on the wires and install the nuts (2).
(c)
Put the clamps (9) in position on the wires and install the bolts (7), the washers (8) and the clamps (9).
(d)
Refer to the match marks and put the wires (6) in position.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备3(12)
