_______ YOU CONNECT THE ELECTRICAL WIRES. IF YOU MAKE AN ERROR WHEN YOU CONNECT THE WIRES YOU WILL CAUSE DAMAGE TO EQUIPMENT.
1 Put the wires (6) in position and install the nuts (5).
_
(f)
Put the cover (3) in position and install the screws (4). WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE LOCKWIRE.
_______ CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
(g)
Safety the screws (4) with MISCELLANEOUS (Material No. 19-010).
(j)
Put the workbenches (41) and (42) in position on the galley module (32) and install the remaining screws (44).
(k)
Install the L-profiles (37).
(l)
Put the divider panels (21) and (22) in position on the galley module (35) and install the screws (20).
(m)
Put the pelmet (18) in position on the galley module (31) and install the screws (19).
(n)
Put the extractor (28) in position and install the screws (29).
(6) Seal the Splitline Joints of the Galley Unit
(a) Remove the old sealant of the splitline joints with a nonmetallic-scraper.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(b) Clean the splitline joints with CLEANING AGENTS (Material No. 11-003) and a lint-free cloth.
(c) Apply new BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004A) into all the splitline joints.
R **ON A/C 051-099,
R Subtask 25-33-41-420-052-C
R C. Connect the Galley Splitline
R R NOTE : This procedure is only necessary if you removed the galley from____ the cabin.
R R NOTE : Unless specified TORQUE all nuts, bolts and screws (Ref. TASK 20-____ 21-11-911-001).
R R (1) Connect the Galley at the Splitline (Ref. Fig. 405A/TASK 25-33-41-991-014-B)
R R WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME_______ DAMAGED OR INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.
R (a) Prevent damage to the component interface and the adjacent area.
R R (b) Carefully put the galley modules (1), (4), (15) and (16) in position in the aircraft.
R (c) Install the screws (12) and the strips (13).
R (d) Install the screws (11) and the strips (10).
R (e) Install the screws (6) and (20) and the plates (5) and (21).
R (f) Install the screws (2) and the strips (3).
CES
R (g) Install the screws (22) and the doors (23).
R (h) Put the workdeck (24) in position and install the screws (14) and
R (25).
R (i) Install the bolts (28) and the washers (29).
R (j) Install the screws (26) and the covers (27).
R (k) Install the screws (17) and (8) and the side covers (18) and (7).
R (l) Close the doors (9) and (19).
R (2) Connect the Splitline Supply Connections
R (Ref. Fig. 406/TASK 25-33-41-991-032-A)
R (a) Connect the ring (11) to the drain cable (10) and the drain valve
R (12).
R (b) Remove the blanking plugs from the disconnected line ends.
R (c) Connect the drain pipe (6) to the sink (4) and install the clamp
R (5).
R (d) Connect the exhaust-air hose (3) to the manifold (1) and install
R the clamp (2).
R (e) Connect the drain pipe (9) to the pipe (7) and install the clamp
R (8).
R (f) Connect the potable water pipe (15) to the fittings (13) and
R tighten the nuts (14).
R (3) Connect the Splitline Electrical Connections
R (Ref. Fig. 407/TASK 25-33-41-991-031-A)
R (a) Install the bolts (5), the washers (4) and the clamps (3).
R (b) Remove the blanking caps from the electrical connectors.
R (c) Make sure that the electrical connectors are clean and in the
R correct condition.
R (d) Connect the elctrical connectors (2) to the receptacles (1).
R (e) Connect the electrical connectors (6) to the junction receptacle
R (7).
R Subtask 25-33-41-420-059-C
R D. Installation of the Galley Unit
R NOTE : Unless specified TORQUE all nuts, bolts and screws. (Ref. TASK 20-____
R 21-11-911-001)
R (1) Install the Lower Attachments
R (Ref. Fig. 404A/TASK 25-33-41-991-013-B)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备3(30)
