KICK PLATE
BOLT AND BOLT AND WASHER WASHER
CARPET
FLOOR FITTING FLOOR FITTING
FLOOR ATTACHMENT FLOOR ATTACHMENT
G H
GALLEY NO. 2
SCREW STABILIZER FITTINGSEALANT
STABILIZER FITTING
I
Forward Galley Installation
Figure 401 (Sheet 4)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
25-31-53
ALL ú ú 11 Page 406 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 024-188
CAUTION:_______DO NOT CAUSE DAMAGE TO THE MOISTURE BARRIER. DAMAGE TO THE FLOOR PANELS CAN OCCUR IF YOU CAUSE DAMAGE TO THE MOISTURE BARRIER.
(16)
Remove the fillet seal from around the bottom of the galley.
S 024-189
(17)
For galley No. 2, lift the galley until you can remove the stabilizer fitting and floor seal from the bottom of the galley.
S 024-060
(18)
Remove the galley.
TASK 25-31-53-404-062
3. Forward Galley - Installation (Fig. 401)_____________________________
A. Consumable Materials
(1)
A00027 Adhesive, General - BAC5010, Type 60,
(2)
A00246 Sealant, Pressure, Environmental and
Fuel Cavity - BMS 5-95, Class B
(Preferred); BMS 5-79, Class B,
(Alternative) (AMM 20-30-11/201).
(3)
Solvent, General Purpose Cleaning - BMS 3-2
(AMM 20-30-31/201).
(4)
A00344 Corrosion Preventive Compound (Grease) -MIL-C-11796, Class 3
B. References
(1)
AMM 24-22-00, MP - Electrical Power, Control
(2)
AMM 25-31-83/401, Forward Galley Header
(3)
AMM 38-41-00/201 - Water Tank Pressurization System
(4)
AMM 51-21-92/201 - Floor Track Corrosion Prevention
(5)
AMM 53-21-00/201- Passenger Cabin Floor
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
25-31-53
ALL ú ú 13 Page 407 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
C. Access
(1) Location Zone
100 Upper Half of the Fuselage
D. Procedure
S 164-064
(1)
Clean the moisture barrier that is on the floor in the galley area.
S 364-232
(2)
Repair the moisture barrier if it is necessary (AMM Chapter 53, Passenger Cabin Floor).
S 624-066
(3)
Apply a corrosion prevention compound in the floor tracks
(AMM 51-21-92/201).
S 424-067
(4)
Put the galley in its position and examine the flange for the correct fit. The flange contour must be equivalent to the internal contour and be approximately 1/2 inch from the cabin lining panels.
NOTE: If you installed the same galley as you removed, it is not
____
necessary to change the flange.
If you installed a replacement galley, it can be necessary to change the flange to get a satisfactory fit as follows:
(a)
Move the galley inboard.
(b)
Cut the galley flange if it is necessary.
(c)
Put the galley in its position.
S 424-196
(5) Install the floor (seat track) attachment fittings:
(a) Put the anchor fitting and the plungers in the floor track through the wells in the galley floor.
NOTE: Make sure you lift the plunger sufficiently in the
____ fitting to be clear of the tabs on the floor track.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
25-31-53
ALL ú ú 19 Page 408 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 EQUIPMENT/FURNISHINGS(90)
