S 147-021
(2) To clean by the usual procedure, do these steps:
(a) Mix 2 ounces of Orvus WA paste in one gallon of water.
NOTE: You can also use Do-All, Calla 301A Lemon or Calla
____ 301A Standard. Refer to the Prepare to Clean paragraph for the instructions to mix the detergents.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
25-01-12
ALL ú ú 03 Page 712 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(b)
Apply only the foam to the leather or Naugahyde with a soft cloth. Rub carefully in a circular movement.
(c)
Remove the detergent with a clean cloth that is moist with water.
(d)
Rub the surface with a dry soft cloth.
N. Clean the Painted, Plastic or Rubber Floor Coverings
S 147-022
(1)
Use a vacuum cleaner to remove loose unwanted materials.
S 147-023
(2)
Apply mixed detergent to the floor covering.
S 147-017
(3)
Rub the surface with a brush that has medium-fiber bristles, if it is necessary.
S 147-024
(4)
Flush the surface with clean water.
S 147-003
(5)
Remove the loose unwanted materials with paper towels or wipers.
S 147-025
(6)
Do the steps again until the surface is fully clean.
O. Clean the Silicone Seals
S 117-030
(1)
Apply mixed detergent with a spray bottle or sponge.
S 117-038
(2)
Let it soak on the seal for one-half to two minutes.
(3)
Rub the surface of the seal with a cloth that is moist with water.
S 147-032
(4)
Remove the detergent from the seal with a clean wiper that is soaked with water.
(5)
Dry the seal with a clean, dry cloth.
S 147-031
S 147-033
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
25-01-12
ALL ú ú 02 Page 713 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
P. Clean the Bare Metal Surfaces
S 167-034
CAUTION: USE ONLY CLEAN WATER OR CHLORINATED WATER TO CLEAN THE FRONT
_______ COVERS OF OVENS. DETERGENTS CAUSE DETERIORATION OF THE SURFACE FINISH. DO NOT USE POLISHES ON DECORATIVE ALUMINUM. THE POLISHES CAN CAUSE DAMAGE TO THE DECORATIVE SURFACES.
(1) To clean a small area of an aluminum surface, do these steps:
(a)
Remove the loose unwanted material with a wiper.
(b)
Apply mixed detergent to the dirty area with a spray bottle or a moist sponge.
(c)
Carefully rub the area with a clean wiper to remove the unwanted material.
(d)
Remove the detergent with a sponge that is moist with water.
(e)
Dry the surface with a clean wiper. Rub the surface in a straight line movement. If the area is still dirty, do these steps:
WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR ON YOUR SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. SOLVENTS MAY BE FLAMMABLE OR HARMFUL TO THE ENVIRONMENT. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
CAUTION:_______DO NOT USE MORE FREOM THAN IS NECESSARY. MAKE SURE YOU PREVENT THE CONTAMINATION OF THE ADJACENT CLEAN AREAS BY THE FREON. IF YOU USE TOO MUCH FREON, DAMAGE TO THE PARTS WILL OCCUR.
1) Rub the area with a wiper that is moist with solvent, Series 84 (AMM 20-30-84/201) or Freon TF. 2) After the surface looks fully clean, remove the solvent, Series 84 (AMM 20-30-84/201) with a mixed detergent.
S 147-006
(2) To clean the aluminum with a usual procedure, do these steps:
(a)
Apply mixed detergent to the surface with a sponge or a spray bottle.
(b)
Let it soak on the surface for one-half to two minutes.
(c) 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：737-300 400 500 AMM 飞机维护手册 EQUIPMENT/FURNISHINGS(10)
