737-300 400 500 AMM 飞机维护手册 起落架 LANDING GEAR 3(79)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

34 seconds  Right inboard wheel speed switch defective  Verify that ABS button on front panel of antiskid had been depressed while auto-matic test was in progress. If ABS button was depressed:  Replace antiskid control unit 
36 seconds  Solenoid valve pressure switch or solenoid valve defective (switch psi when solenoid valve is energized) indicates < 1000  (1) (2) (3) Rerun test with jumper between pin 2 and 3 on If system passes, Check that system B hydraulic pressure is on solenoid switch connector D2572 Between 27 and 34 sec-onds into test remove jumper If system disarms at about 36 seconds,  Replace solenoid valve pressure switch Replace solenoid valve 
38 seconds or  Servo valve pres- Check that ground is at 
42.7 seconds  sure switch or servo valve defective (switch psi when 350 psi 42.7 sec) commanded at commanded at 38 sec or 570 psi indicates > 1000  pin 54 of D1040 antiskid module connector If ground If no ground,  Replace servo valve pressure switch Replace servo valve 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-43-01
 ALL  ú ú 01 Page 106 ú Feb 25/86
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
TROUBLE  PROBABLE CAUSE  ISOLATION PROCEDURE  REMEDY 
45.3 seconds After 62 seconds when brake pedals stop flashing light does not depressed After 62 seconds (light on steady when position 1 selected in air mode end of test) 57 seconds (light flashes 5 sec. and goes on steady without depressing brake pedals) 57 seconds (NO LIGHT)  Servo valve pressure switch or servo valve defective (switch psi when 1380 psi indicates < 1000 z zcommanded) brake pedal switch defective S762 or S763 R290 A/B disarm relay defective S762 or S763 brake pedal switch shorted L736 defective or M162 antiskid control module illumination function failed) defective (Light  If pressure at disarm Repeat test with pressure gage on bleed port of any brake. Observe brake pres-sure at time of disarm If pressure at disarm > 1200 psi, < 1200 psi, Check for ground at pin 18 on D1040 antiskid control module when either brake Turn autobrake selector switch OFF and then to position 1. Verify 28 VDC on pins 13, 17, 21, 23, 35 of D1040. Jumper pin 13 to ground (energizes disarm relay) then remove jumper. If voltage at pins 17, 21, 23, 35 of D1040 not 0 volts -Check for open circuit (greater than 50,000 ohms) between pin 18 on D1040 antiskid control module and ground with both brake pedals released. If check fails: pedal is depressed. If check fails: Do a check of L736 with the Master Test and Dimming Panel. If the light did not illuminate: Check for continuity between the L736 autobrake disarm light and pin 11 of the D1040 antiskid control module connector. Switch on the Captain's P1 If there is continuity:  Replace servo valve pressure switch valve Replace servo Replace S762 or S763 Repair wiring if required Replace R290 A/B disarm relay NOTE:____ Blue dot of R290 should be con-nected to pin 2. Replace S762 or S763 Repair wiring if required Replace L736 Repair the wiring as required Replace M162 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-43-01
 ALL  ú ú 01 Page 107 ú Nov 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 AUTOMATIC BRAKING SYSTEM - ADJUSTMENT/TEST
__________________________________________
 1.  General
 A.  Use the built-in test features on the front of the antiskid module to do a test on the automatic braking system.
 B.  The module is found on the E3-2 rack in the electronics area aft and to the right of the access hatch (Fig. 501).
 TASK 32-43-01-705-001
 2.  Automatic Braking System Test______________________________
 A.  Standard Tools and Equipment
 (1)  
Pressure gages - 0-4000 psi for hydraulic fluid BMS 3-11

 (2)  
Chocks - Wheel

 (3)  
Stopwatch

 B.  
References

 (1)  
24-22-00/201, Manual Control

 (2)  
29-15-00/201, Hydraulic System

 (3)  
32-00-01/201, Ground Locks

 C.  
Access

 (1)  
Location Zone
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 起落架 LANDING GEAR 3(79)