(b)
Make sure the ENG NO. 2 loop-A and loop-B INOP lights on the M279 module come on.
S 865-118
(6) Close the FIRE PROTECTION DETECTION ENG NO. 2 circuit breaker on the P6-2 panel.
(a)
Make sure the FAULT light goes off.
(b)
Make sure the ENG NO. 2 loop-A and loop-B INOP lights go off.
S 865-119
(7) Hold in the FAULT TEST SW switch on the M279 module.
(a)
Make sure the APU DET INOP and FAULT lights on the P8-1 panel come on.
(b)
Make sure the five lights on the M279 module come on.
S 865-120
(8) Release the FAULT TEST SW switch.
(a)
Make sure these lights on the P8-1 panel are off:
1) The FAULT light
2) The APU DET INOP light
(b)
Make sure these lights on the P7 panel are off:
1) The two MASTER CAUTION lights
2) The OVHT/DET annunciator
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
26-11-00
ALL ú ú 02A Page 521 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(c) Make sure these lights on the M279 panel are off: 1) The four engine INOP and one APU INOP
S 865-055
(9) Make sure there are no indications of failure, or systems that do not operate.
M. Put the airplane back to its usual condition
S 865-122
(1) Remove electrical power if it is no longer necessary
(AMM 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
26-11-00
ALL ú ú 03A Page 522 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
ENGINE FIRE DETECTION SYSTEM DETECTOR - REMOVAL/INSTALLATION
____________________________________________________________
1. General_______
A. Each engine has four Engine Fire Detector Elements; one detector is on the right side of the strut above the fan case, one detector is on the upper left side of the fan case, one detector is on the underside of the fan case, and one detector is around the engine core. You can access the three detectors in the fan area by opening the fan cowl panel, you can access the core detector by opening the fan duct cowl and thrust reviser halves.
TASK 26-11-11-004-001
2. Remove the Detector (Fig. 401)___________________
A. References
(1) AMM 24-22-00/201, Manual Control
B. Remove the Detector
S 014-002
(1)
Open the FIRE PROTECTION DETECTION ENG NO 1 or ENG NO 2 circuit breaker on the P6 panel.
S 014-003
(2)
Open the fan cowl panel (AMM 71-11-02/201) or the fan duct cowl and thrust reverser halves (AMM 78-31-00/201).
S 034-005
(3)
AIRPLANES WITH PIN-SOCKET CONNECTORS; Remove the electrical connectors from each end of the detector.
S 434-036
(4)
Install caps on the electrical connectors.
S 034-006
(5)
AIRPLANES WITH TERMINAL LUG CONNECTORS; Remove the nut, washer, and screw from the terminal lug connectors.
(6)
Remove the jamnuts from the detector end fittings.
S 094-010
(7)
Release the support tube clamps along the length of the detector.
(8)
Remove the detector.
S 034-009
NOTE:____Hold the detector when you release the clamps. Do not bend the detector.
S 024-011
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
26-11-11
ALL ú ú 02 Page 401 ú Jul 12/00
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 防火 FIRE PROTECTION(25)
