曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
(d) Rotate the captain’s control wheel to the full left and hold.
1) Make sure the rudder moves 2.47 in. (62.7 mm) ±0.25 in. (6.35 mm) (2.4 +/- 0.3
degrees) to the left side.
(e) Put the captain’s control wheel back to the neutral position.
(f) Rotate the captain’s control wheel to the full right and hold.
1) Make sure the rudder moves from left to right.
2) Make sure the rudder moves 2.47 in. (62.7 mm) ±0.25 in. (6.35 mm) (2.4 +/- 0.3
degrees) to the right side.
(g) Put the captain’s control wheel back to the neutral position.
SUBTASK 27-21-00-860-165-002
(7) Return the flaps to the retracted postion. To retract them, do this task: Retract the Trailing Edge
Flaps, TASK 27-51-00-860-804.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 006-099, 101-122; GUN 001-005, 155-157, 201-999
POST SB 737-27-1253
27-21-00
Config 2
Page 561
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-21-00-860-124-002
(8) Do this task: Put the Rudder Hydraulic systems A, B, and Standby Back to the Condition
Before the Pressurization, TASK 27-21-00-840-801.
------------------------- END OF TASK ---------------------------
TASK 27-21-00-700-821-002
15. Rudder Hinge Friction Test
Figure 503
A. General
(1) Use this test to verify that the rudder hinge friction is within limit.
B. References
Reference Title
27-21-00-800-802 Remove Pressure from the Rudder Hydraulic Systems A, B, and
Standby (P/B 201)
C. Tools/Equipment
Reference Description
STD-753 Scale - Push/Pull, 0-25 pound (0-11 kilogram) Capacity, 1/4 pound
(113 gram) Accuracy
STD-1238 Indicator - Dial
STD-1278 Block - Loading, 1/8 Inch Thick, 3 Inch by 3 Inch Wood or Fiberglass
Block with Pad to Prevent Damage to the Skin.
STD-1279 Mount - Device, Mounting, Holds the Dial Indicator
D. Location Zones
Zone Area
324 Vertical Fin - Rear Spar To Trailing Edge
E. Procedure
SUBTASK 27-21-00-860-125-002
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDER,
ELEVATORS, FLAPS, SPOILERS, SLATS, AND THRUST REVERSERS CAN MOVE
QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO
PERSONS AND DAMAGE TO EQUIPMENT.
(1) If hydraulic pressure is powered, do this step to turn off hydraulic power:
(a) Do this task: Remove Pressure from the Rudder Hydraulic Systems A, B, and Standby,
TASK 27-21-00-800-802.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 006-099, 101-122; GUN 001-005, 155-157, 201-999
POST SB 737-27-1253
27-21-00
Config 2
Page 562
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-21-00-730-024-002
CAUTION: USE A LOADING BLOCK AND DO NOT PUT MORE THAN 50 LBF (222 N) ON THE
RUDDER WHEN YOU MOVE THE RUDDER SURFACE BY AN EXTERNAL FORCE.
APPLY THE EXTERNAL FORCE APPROXIMATELY AT BETWEEN 6 INCHES (162
MILLIMETERS) AND 18 IN. (457 MM) FROM THE BOTTOM OF THE TRAILING EDGE
AND APPROXIMATELY 3 IN. (76 MM) FORWARD OF THE TRAILING EDGE. IF YOU DO
NOT APPLY FORCE AT THIS LOCATION, YOU CAN CAUSE DAMAGE TO THE RUDDER
(2) Do the rudder hinge friction check:
NOTE: If the dial indicator is not available, you can use a ruler to measure the rudder trailing
edge placement in this test.
(a) Make sure the rudder and rudder pedals are in the neutral position.
(b) Make sure the rudder trim indicator is at zero units of trim.
(c) Use a block, STD-1278 and push/pull scale 0-25 pound (0-11 kilogram), STD-753 to move the
rudder fully to the left side.
1) Verify that there is no sign of binding, rough spots or excessive friction at any point of
travel.
a) If binding or excessive friction exist, the bearings may be out of alignment,
damaged or improperly installed. Correct this condition and repeat this check.
(d) Use a block, STD-1278 and push/pull scale 0-25 pound (0-11 kilogram), STD-753 to move the
rudder fully to the right side.
1) Verify that there is no sign of binding, rough spots or excessive friction at any point of
travel.
a) If binding or excessive friction exist, the bearings may be out of alignment,
damaged or improperly installed. Correct this condition and repeat this check.
(e) Attach the mount, STD-1279 on the tail cone.
(f) Place the pointer of the dial indicator, STD-1238 at the lower aft corner of the rudder trailing
edge.
(g) Use a block, STD-1278 and push/pull scale 0-25 pound (0-11 kilogram), STD-753 to move the
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飞机维护手册2(72)
