曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
NOTE: The leading edge flaps and slats will move to the retracted position when you supply
hydraulic power if they are not in the retracted position.
SUBTASK 27-51-00-860-063
WARNING: MOVE ALL PERSONS AND EQUIPMENT AWAY FROM THE TRAILING EDGE FLAPS.
THE FLAPS WILL MOVE AND CAN CAUSE INJURIES TO PERSONS OR DAMAGE TO
EQUIPMENT.
(2) Move the flap control lever to the applicable detent position.
SUBTASK 27-51-00-860-064
(3) To retract the trailing edge flaps, move the flap control lever to the UP position.
SUBTASK 27-51-00-860-065
(4) Remove system B hydraulic power, do this task: Hydraulic System A or B Power Removal,
TASK 29-11-00-860-805.
J. Trailing Edge Flap Operation With Alternate Control
NOTE: Make sure you do the Disable the Leading Edge Slats part of this task before you operate
the trailing edge flaps.
SUBTASK 27-51-00-860-066
WARNING: MOVE ALL PERSONS AND EQUIPMENT AWAY FROM THE TRAILING EDGE FLAPS.
THE FLAPS WILL MOVE AND CAN CAUSE INJURIES TO PERSONS OR DAMAGE TO
EQUIPMENT.
(1) Move the ALTERNATE FLAPS ARM switch on the P5 panel to arm the alternate control system.
SUBTASK 27-51-00-860-067
CAUTION: WAIT A MINIMUM OF 15 SECONDS AFTER THE FLAPS STOP BEFORE YOU USE THE
ALTERNATE SYSTEM TO MOVE THE FLAPS AGAIN. YOU CAN CAUSE DAMAGE TO
THE FLAP ALTERNATE MOTOR.
(2) Move the ALTERNATE FLAPS control switch to DOWN to extend the trailing edge flaps as it is
necessary.
SUBTASK 27-51-00-860-068
(3) Move the ALTERNATE FLAPS control switch to the OFF position.
SUBTASK 27-51-00-860-069
WARNING: MAKE SURE THE POSITION OF THE FLAPS AGREES WITH THE POSITION OF THE
FLAP CONTROL LEVER. WHEN YOU SUPPLY HYDRAULIC POWER, THE FLAPS AND
SLATS WILL MOVE AUTOMATICALLY TO THE POSITION OF THE FLAP CONTROL
LEVER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(4) To retract the trailing edge flaps, move the ALTERNATE FLAPS control switch to UP until the
flaps are in the same position as the flap control lever.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-00
Page 218
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-51-00-860-070
(5) Move the ALTERNATE FLAPS control switch to the OFF position.
SUBTASK 27-51-00-860-071
(6) Move the ALTERNATE FLAPS ARM switch to the OFF position to disarm the alternate control
system.
SUBTASK 27-51-00-080-003
(7) Remove the lock, SPL-1675 from the standby hydraulic module (Figure 205):
(a) Remove the lockpin.
(b) Remove the lock, SPL-1675 from the standby hydraulic module.
(c) Make sure the override lever at the leading edge standby drive shutoff valve is in position
1.
(d) Before you connect the electrical connector, examine the connector for corrosion.
WARNING: DO THE STEPS BELOW IF THE AIRPLANE OPERATES AT AIRPORTS WHERE
DEICING FLUID THAT CONTAIN POTASSIUM FORMATE IS USED. ALSO DO THE
STEPS FOR ALL AIRPLANES THAT YOU FOUND CORROSION IN THE
ELECTRICAL CONNECTORS IN THE MAIN WHEEL WELL. THE ELECTRICAL
CONNECTOR IS PART OF A SYSTEM THAT IS NECESSARY FOR SAFE FLIGHT.
(e) If there was corrosion, refer to (SWPM 20-60-03) to correct the problem.
(f) Apply the D5026NS or ZC-026 compound, G50171 to the connector (SWPM 20-60-03).
(g) Connect the electrical connector to the leading edge standby drive shutoff valve.
K. Trailing Edge Flap Manual Operation
(Figure 203)
NOTE: Make sure you do the Disable the Leading Edge Slats part of this task before you operate
the trailing edge flaps.
SUBTASK 27-51-00-480-003
(1) Install DO-NOT-OPERATE tags on the flap control lever, the ALTERNATE FLAPS switches and
the hydraulic control switches.
SUBTASK 27-51-00-040-005
WARNING: DO THE TRAILING EDGE FLAP DEACTIVATION PROCEDURE BEFORE YOU DO WORK
ON THE FLAP SYSTEM. WITH THE FLAPS ACTIVATED, THE FLAPS CAN MOVE AND
CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(2) Do this task: Trailing Edge Flap System Deactivation, TASK 27-51-00-040-801.
SUBTASK 27-51-00-010-008
(3) Remove the cover [4] from the flap power drive unit [1]:
(a) Remove the bolts [3] and washers [2] that attach the cover [4] to the flap power drive unit
[1].
(b) Remove the cover [4] from the power drive unit [1]
SUBTASK 27-51-00-980-005
WARNING: MOVE ALL PERSONS AND EQUIPMENT AWAY FROM THE FLAPS. THE FLAPS WILL
MOVE AND CAN CAUSE INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-00
Page 219
Jun 10/2005
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飞机维护手册4(38)
