曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
B. References
Reference Title
27-51-13-000-801 Inboard Flap Outboard Carriage Removal (P/B 401)
27-51-13-400-801 Inboard Flap Outboard Carriage Installation (P/B 401)
C. Tools/Equipment
Reference Description
STD-1096 Micrometer - Depth, 0-1 Inch, Readable to 1/1000 Inch
STD-1097 Caliper - Vernier, 0-6 Inch, Readable to 1/1000 Inch
D. Location Zones
Zone Area
542 Left Wing - Fairing Flap Support No. 3
642 Right Wing - Fairing Flap Support No. 6
E. Procedure
SUBTASK 27-51-13-020-006
(1) Do this task: Inboard Flap Outboard Carriage Removal, TASK 27-51-13-000-801.
SUBTASK 27-51-13-020-007
(2) Use these tools to do a check for wear on the part of the inboard flap outboard carriage:
(a) micrometer (0-1 Inch, readable to 1/1000 Inch), STD-1096
(b) readable to 1/1000 inch vernier 0 - 6 inch caliper, STD-1097.
SUBTASK 27-51-13-020-008
(3) Examine the parts of the inboard flap outboard carriage (Table 601):
(a) Remove the parts that you will measure.
(b) Measure the parts with a micrometer (0-1 Inch, readable to 1/1000 Inch), STD-1096 or a
readable to 1/1000 inch vernier 0 - 6 inch caliper, STD-1097.
(c) Compare the dimensions you measured with the permitted wear dimensions.
(d) If the parts are not in tolerance, replace or repair the parts.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-13
Page 601
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Table 601/27-51-13-993-805
NAME OF THE PARTS
THAT ARE IN CONTACT
DIM.
DIAMETER DESIGN LIMITS WEAR LIMITS
MINIMUM
inches/mm
MAXIMUM
inches/mm
PERMITTED
MAXIMUM I.D./
MINIMUM O.D. OF
WORN PART
MAXIMUM
SERVICE
CLEARANCE
inches/mm
#1 BUSHING I.D. 1.1870 in 1.1878 in 1.1915 in
30.150 mm 30.170 mm 30.264 mm 0.0050 in
#1 PIN O.D. 1.1855 in 1.1865 in 1.1828 in 0.1270 mm
30.112 mm 30.137 mm 30.043 mm
#2 ROLLER I.D. 1.1868 in 1.1875 in 1.1915 in
30.145 mm 30.163 mm 30.264 mm 0.0050 in
#2 PIN O.D. 1.1855 in 1.1865 in 1.1825 in 0.1270 mm
30.112 mm 30.137 mm 30.036 mm
#3 ROLLER O.D. 2.9990 in 3.0010 in 2.9970 in
76.175 mm 76.225 mm 76.124 mm
#4 ECCENTRIC
BUSHING
I.D. 1.2500 in
31.750 mm
1.2520 in
31.801 mm
1.2540 in
31.852 mm
0.0050 in
#4 PIN O.D. 1.2480 in 1.2490 in 1.2470 in 0.1270 mm
31.699 mm 31.725 mm 31.674 mm
#5 BUSHING I.D. 3.3000 in 3.3020 in 3.3040 in
88.820 mm 83.871 mm 83.922 mm 0.0050 in
#5 CARTRIDGE O.D. 3.2980 in 3.2990 in 3.2970 in 0.1270 mm
83.769 mm 83.795 mm 83.744 mm
#6 ROLLER I.D. 1.2493 in 1.2500 in 1.2540 in
31.732 mm 31.750 mm 31.852 mm 0.0050 in
#6 PIN O.D. 1.2480 in 1.2490 in 1.2450 in 0.1270 mm
31.699 mm 31.725 mm 31.623 mm
#7 ROLLER O.D. 2.9990 in 3.0010 in 2.9970 in
76.175 mm 76.225 mm 76.124 mm
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-13
Page 602
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-51-13-420-006
(4) Do this task: Inboard Flap Outboard Carriage Installation, TASK 27-51-13-400-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-13
Page 603
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Inboard Flap Outboard Carriage Inspection
Figure 601 (Sheet 1 of 2)/27-51-13-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-13
Page 604
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Inboard Flap Outboard Carriage Inspection
Figure 601 (Sheet 2 of 2)/27-51-13-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-13
Page 605
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-51-13-200-802
3. Inboard Flap Inboard Carriage Inspection
(Figure 602)
A. General
(1) This task gives wear limits for the inboard carriage on the inboard flap.
(2) This task is applicable to the carriages at flap supports No. 4 and 5.
B. References
Reference Title
27-51-13-000-802 Inboard Flap Inboard Carriage Removal (P/B 401)
27-51-13-400-802 Inboard Flap Inboard Carriage Installation (P/B 401)
C. Tools/Equipment
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飞机维护手册4(107)
