曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
NOTE: A threaded wire is attached to the switch electrical cable.
(a) Slowly pull the switch electrical cable through the control wheel handle with the other end
of the threaded wire.
(b) Install the insulator [6] between the switch assembly [1] and the interphone switch wires.
(c) Put the switch assembly [1] in its position.
(d) Install the screws [5] to hold the switch assembly [1] to the control wheel.
1) Tighten the screws [5] to 4.0 ±0.5 in-lb (0.45 ±0.06 Nm).
2) Make sure there is 0.002 in. (0.05 mm) clearance between the control wheel handle and
switch assembly [1].
(e) Remove the threaded wire from the switch electrical cable.
(f) Install the terminals on the switch wires.
(g) Install the screws [9], washers [8], and washers [10] to connect the terminals of the switch
wire to the terminal block [7].
1) Make sure that the terminals are installed correctly according to the color code
identification (Figure 401).
SUBTASK 27-41-97-420-002
(2) Install the screws [4] to attach the terminal block cover [3] to the control wheel.
SUBTASK 27-41-97-420-003
(3) Install the medallion [2] on the control wheel.
SUBTASK 27-41-97-860-006
(4) Remove the safety tag and close this circuit breaker:
F/O Electrical System Panel, P6-2
Row Col Number Name
B 10 C00207 FLIGHT CONTROL STAB TRIM CONT
SUBTASK 27-41-97-710-003
(5) Do this task: Stabilizer Trim Control Switch Test, TASK 27-41-97-700-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-97
Page 405
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
STABILIZER TRIM CONTROL SWITCH - ADJUSTMENT/TEST
1. General
A. This procedure has this task:
(1) Stabilizer Trim Control Switch Test - Use this test to make sure that the stabilizer trim control
switches operate correctly.
B. The stabilizer trim control switches are installed on the control wheels. Each control wheel has two
stabilizer trim control switches.
C. This procedure is applicable for the stabilizer trim control switches on the captain’s and first officer’s
control wheels.
TASK 27-41-97-700-801
2. Stabilizer Trim Control Switch Test
A. References
Reference Title
24-22-00-860-811 Supply Electrical Power (P/B 201)
B. Location Zones
Zone Area
211 Flight Compartment - Left
212 Flight Compartment - Right
C. Prepare for the Test
SUBTASK 27-41-97-860-001
(1) Do this task: Supply Electrical Power, TASK 24-22-00-860-811.
SUBTASK 27-41-97-860-002
(2) Make sure that these circuit breakers are closed:
F/O Electrical System Panel, P6-2
Row Col Number Name
B 10 C00207 FLIGHT CONTROL STAB TRIM CONT
D 10 C00840 FLIGHT CONTROL STAB TRIM ACTUATOR
SUBTASK 27-41-97-860-003
(3) Make sure that the main cutout switch (S272) on the control stand is in the NORMAL position.
SUBTASK 27-41-97-860-004
(4) Make sure that the column actuated stabilizer trim (override) switch on P8-47 module is in the
NORM position.
D. Stabilizer Trim Control Switch Test
SUBTASK 27-41-97-710-001
(1) Do a test of the stabilizer trim control switches on the applicable control wheel:
(a) Push and hold the two stabilizer trim control switches on the applicable control wheel to the
NOSE DOWN position.
1) Make sure the stabilizer leading edge moves up.
2) Make sure the trim wheels turn in the nose down position.
3) Make sure that the STAB TRIM indicator for the applicable control wheel moves in the
NOSE DOWN position.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-97
Page 501
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
4) Release the two stabilizer trim control switches.
(b) Push and hold the two stabilizer trim control switches on the applicable control wheel to the
NOSE UP position.
1) Make sure the stabilizer leading edge moves down.
2) Make sure the trim wheels turn in the nose up position.
3) Make sure that the STAB TRIM indicator for the applicable control wheel moves in the
NOSE UP position.
4) Release the two stabilizer trim control switches.
5) Move the horizontal stabilizer to the neutral position.
(c) Push and hold the left stabilizer trim control switch on the applicable control wheel to the
NOSE UP position.
1) Make sure the stabilizer leading edge does not move.
2) Release the left stabilizer trim control switch.
(d) Push and hold the left stabilizer trim control switch on the applicable control wheel to the
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飞机维护手册4(28)
