(2)
The second task finds the zero index mark on the N2 rotor
(3)
The third task gives general inspection and removal/installation instructions for engine tubes, hoses, and fittings.
NOTE: The assemblies included in this task do not contain parts
____ that have regular replacement or inspection schedules.
B. For this procedure the accessory gearbox will be referred to as the AGB, the N2 rotation pad drive will be referred to as the drive pad and the N2 rotation pad drive cover will be referred to as the cover.
TASK 72-00-00-982-026-C00
2. Turn the N2 Rotor
_________________
A. General
(1) This task contains the data to turn the N2 rotor manually or with a drive motor.
B. Equipment
(1)
Drive motor - N2 rotor rotation,
foot control, 856A2002P03,
CFM International, P.O. Box 15514,
Cincinnati, OH 45215
(2)
Drive motor - N2 rotor rotation, hand control,
856A2002P04,
CFM International, P.O. Box 15514,
Cincinnati, OH 45215
C. Consumable Materials
(1)
D00601, Grease, (CP2101) graphite - GP460, Aeroshell 8
(2)
D00599, Oil (CP2442) engine - CFMI SB 79-001
D. References
(1) AMM 71-11-02/201, Fan Cowl Panels
E. Access
(1) Location Zones
502/602 Fan Cowl Panels - Left
506/606 Engine
F. Prepare to Turn the N2 Rotor.
S 822-032-C00
CAUTION: DO NOT TURN THE ENGINE IF ITS ENGINE FIRE SWITCH HAS BEEN
_______ PULLED. DAMAGE TO THE ENGINE DRIVEN HYDRAULIC PUMP (EPD) CAN OCCUR.
(1) Make sure the engine fire switch for the applicable engine has not been pulled.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-00-00
ALL ú ú C01 Page 201 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 012-027-C00
(2)
Open the left fan cowl panel (AMM 71-11-02/201).
S 012-028-C00
(3)
At the 9 o'clock position on the AGB, remove the cover as follows
(Fig. 201):
(a)
Remove the lockwire and remove the 5 bolts that attach the cover to the drive pad.
(b)
Move the cover until it is away from the drive pad.
NOTE: Do not remove the lanyard that attaches the cover to
____
the AGB.
(c) Discard the two O-rings.
NOTE: On engines PRE-CFMI-SB 72-155, there is only one
____
O-ring.
G. Turn the N2 Rotor Manually
S 982-053-C00
(1) Do these steps to turn the N2 rotor manually:
(a)
Attach a 3/4-inch square drive tool with a two-foot extension to the drive pad.
(b)
Turn the handle of the tool in the counterclockwise direction as seen from the rear.
NOTE: During engine operation, the engine turns in the
____ clockwise direction as seen from the rear. Because of the AGB gearing, when you turn the tool in the counterclockwise direction as seen from the rear, the engine will turn in the correct clockwise direction.
It is recommended that the N2 rotor be turned in its usual clockwise direction.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 ENGINE 发动机 1(7)
