S 434-011-001
(2)
If the fuel solenoid valve was removed from the fuel control unit, install the fuel solenoid valve (AMM 49-31-31/401).
S 434-012-001
(3)
If the low pressure fuel filter was removed from the fuel control unit, install the low pressure fuel filter (AMM 49-31-21/401).
S 424-013-001
(4)
Install the fuel control unit to the APU:
(a) Remove the caps and the plugs from all the disconnected lines and the ports.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITHOUT THE TAFCU ú
49-31-11
ú CONFIG 1 ú 01 Page 404 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(b) FUEL CONTROL UNIT WITH THE DRIVE SHAFT; Lubricate the drive shaft: 1) Pull the drive shaft out in a straight line to remove it
from the fuel control unit. 2) Apply a thin layer of grease to the flat areas of the
square drive. 3) Install the drive shaft into the fuel control unit. 4) Apply a thin layer of grease to the teeth on the drive
shaft for the fuel control unit.
(c)
FUEL CONTROL UNIT WITH THE SPIDER COUPLING ASSEMBLY; Lubricate the half shaft splined coupling: 1) Apply a thin layer of grease to the teeth on the half shaft
splined coupling.
(d)
Carefully put the fuel control unit in its position on the mounting studs. 1) Make sure the drive shaft or half shaft splined coupling
for the fuel control unit engages the gear shaft of the accessory drive.
(e)
Install the washers and nuts that attach the fuel control unit to the APU engine.
NOTE: You do not have to install the nut at the 9 o'clock
____ position (when looking aft). This will make the installation of the fuel control unit easier.
1) Tighten the nuts to 70-90 pound-inches
(7.9-10.2 newton-meters).
(f)
Connect the control air line (compressor discharge air) to the T-fitting adjacent to the base of the fuel control unit.
(g)
Connect the control air line (compressor discharge air) and the control air line (thermostat) to the Y-fitting on the fuel control unit.
(h)
Connect the electrical plug to the fuel solenoid valve. 1) Install a lockwire to the electrical plug.
(i)
Connect the high pressure fuel line to the elbow on the fuel solenoid valve.
(j)
Connect the fuel hose to the elbow on the low pressure fuel filter.
S 874-023-001
(5)
Do a check of the high pressure bleed for the APU fuel system (AMM 49-31-00/201).
S 864-014-001
(6)
Make sure that this circuit breaker is closed:
(a) E3-3 Electrical Shelf, APU Control Unit
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITHOUT THE TAFCU ú
49-31-11
ú CONFIG 1 ú 01 Page 405 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / GTCP85-129 SERIES /737-300/400/500/ ENGINES/MAINTENANCE MANUAL ////////////////////////
S 714-016-001
(7) APUs WITH ALLIEDSIGNAL SB GTCP85-49-7096; Do the APU operation test (AMM 49-11-00/501):
(a)
During the APU operation, examine the fuel control unit for leakage.
(b)
If you found leakage, repair the cause of it.
NOTE: A fuel leakage rate of 1 drop for each minute (2.5 cc
____ for each hour) is permitted from the fuel control unit.
S 714-017-001
(8) APUs WITHOUT ALLIEDSIGNAL SB GTCP85-49-7096; Do the APU operation test (AMM 49-11-00/501):
(a) After the APU operation test, make sure the APU master switch, on the P5 forward overhead panel, is in the OFF position.
S 794-018-001
(9) APUs WITHOUT ALLIEDSIGNAL SB GTCP85-49-7096; Visually examine the APU for any signs of leakage:
(a) If you found signs of leakage, repair the cause of it.
NOTE: A fuel leakage rate of 1 drop for each minute (2.5 cc
____ for each hour) is permitted from the fuel control unit.
S 864-018-001
(10) Attach a DO-NOT-OPERATE tag to the APU master switch on the P5 forward overhead panel.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 AIRBORNE AUXILIARY POWER 2(19)
