52-11-11
ALL ú ú 03 Page 410 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 33 |Spacing Washer | 52-11-10 | 01 | 40 | | | 34 |Nut | | | 25 | | | 35 |Washer | | | 20 | | | 36 |Structure Link | | | 45 | | | 37 |Bolt | | | 10 | | | 38 |Snubber | | | 30 | | | 39 |Nut | 52-11-11 | 09 | 35 | | | 40 |Washer | | | 30 | | | 41 |Bolt | | | 20 | | | 42 |Telescopic Sleeve | | | 40 | | | 43 |Bolt | | | 425 | | | 44 |Bearing Plate (Door 1L) | 53-43-55 | 01 | 75 | | | 45 |Upper Link | 52-11-03 | 02 | 25 | | | 46 |Door Maintenance Access Panel | 52-11-01 | 04 | 25 | | | | (Door 1L) | | | | | | 47 |Bolt | | | 35 | | | 48 |Collar (Door 1L) | 52-11-11 | 09 | 78 | | | 49 |Spring | | | 100 | | | 50 |Felt Keyway Plug | | | 133 | | | 51 |Spacer | | | 105 | | | 52 |Locknut | | | 110 | | | 53 |Lockwasher | | | 115 | | | 54 |Spacer | | | 120 | | | 55 |Bearing | | | 135 | | | 56 |Sleeve/Spacer | | | 140 | | | 57 |Sprocket | | | 145 | | | 58 |Bearing | | | 135 | | | 59 |Shaft | | | 155 | | | 60 |Camplate | | | 76 | | | 61 |Release Handle (Door 1L) | | | 80 | 2.....….........…...................................…..........…......…........1
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-11-11
ALL ú ú 03 Page 411 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
C. References
(1)
52-11-01/401, Main Entry Doors No. 1
D.
Access
(1)
Location Zone
211 Main Deck, Nose to First Door, LH
(2)
Access Panel
211AL Panel, Access - Door Maintenance (Door 1, LH)
831L Door - No. 1 Main Entry, LH
E.
Install the Body Torque Tube
S 434-014
(1)
Assemble the shaft assembly (24), if it is necessary.
(a)
Do these steps to lubricate the shaft assembly (24) near the sprocket (57): 1) Clean the shaft (59), the sprocket (57) and the
sleeve/spacer (56). 2) Apply grease to the inner surfaces of the sprocket (57) and the sleeve (56). 3) Apply grease to all the open surfaces of the two bearings in the sprocket (57).
(b)
Assemble the sprocket (57), the sleeve/spacer (56), and the bearings (55 and 58) on the shaft (59).
(c)
Install the spacer (54), the lockwasher (53), and the locknut (52).
CAUTION:_______DO NOT MAKE THE LOCKNUT (52) TOO TIGHT. IF YOU MAKE THE LOCKNUT (52) TOO TIGHT, THE SPROCKET CANNOT MOVE FREELY AND THE DOOR WILL NOT OPERATE CORRECTLY IN AN EMERGENCY.
(d)
Tighten the locknut (52) with your hand and lock it with the washer tabs.
(e)
Attach the chain (9) to the sprocket (27).
1) Install the pin from the top to connect the chain (9) to the sprocket (57).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-11-11
ALL ú ú 03 Page 412 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
2) Make sure the head of the attachment pin (29) on the rod end is up and the cotter pin is down. 3) Install the cotter pin (25) and one to three washers (26).
NOTE: Use the washers to fill the clearance between
____ the chain (9) and the cotter pin (25).
(f)
Install the spacer (51) above the locknut (52).
(g)
Lubricate the felt keyway plug (50) with grease.
(h)
Install the felt keyway plug (50) in the lockwasher keyway slot of the torque tube.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 舱门 DOORS 1(87)
