EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-09-06
ALL ú ú 01 Page 402 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
CAUTION:_______ BE CAREFUL WHEN YOU INSTALL THE SEAL. DO NOT MAKE CUTS, TEARS, OR HOLES IN THE SEAL. DAMAGE TO THE SEAL CAN EASILY OCCUR.
(b) Use the door seal installation tool (or a smooth, rounded tool) to push the outboard edge of the seal into the seal retainer. Push the seal vertical to the seal edge to keep the seal smooth.
NOTE:____ Use liquid soap to lubricate the seal during the installation
(3) S 424-007Install 2-3 inches of the seal into the seal retainer at the center of each side of the door.
(4) S 424-008Install the remaining parts of the seal.
(5) S 424-009Make the seal smooth. lip of the seal. Remove the wrinkles and the waviness in the
(6) S 864-011Close the door.
(7) S 214-010Visually make sure the lip of the seal is smooth and flat against the bulb seal.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-09-06
ALL ú ú 01 Page 403 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
LIGHT SEALS - REMOVAL/INSTALLATION
__________________________________
1. General_______
A. This procedure contains two tasks. The first task is the removal of the light seal. The second task is the installation of the light seal.
TASK 52-09-07-004-001
2. Remove the Light Seal (Fig. 401)_____________________
A. Procedure
S 024-010
(1)
For a light seal installation at a hinge, do these steps:
(a)
Remove the hinge screws that hold the seal between the hinge and the partition.
(b)
Remove the light seal.
S 024-003
(2) For a light seal that is bonded to the partition, pull the seal to break the adhesive bond between the seal and the partition.
TASK 52-09-07-404-004
3. Install the Light Seal (Fig. 401)______________________
A. Standard Tools and Equipment
(1)
Leather Punch, 0.22 Inch Diameter Hole
B.
Consumable Materials
(1)
B00148 Solvent - Methyl Ethyl Ketone (MEK), TT-M-261
C.
Procedure
S 424-011
(1)
For a light seal installation at a hinge, do these steps:
(a)
Put the light seal in the correct position on the partition.
(b)
Make holes in the seal flange that align with the holes in the hinge.
(c)
Install the decorative screws to hold the seal between the hinge and the partition.
(2)
For a light seal that is bonded to the partition, do these steps:
S 424-012
WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR ON
_______ YOUR SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. SOLVENTS MAY BE FLAMMABLE OR HARMFUL TO THE ENVIRONMENT. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
(a)
Clean the partition surface. Remove the unwanted adhesive with Ethyl Alcohol, or IPA and a clean cloth.
(b)
Apply the adhesive to bond the light seal in the correct position on the partition. Make sure that when the door is closed the seal will be compressed equally along its length.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-09-07
ALL ú ú 01 Page 401 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
LIGHT SEAL INSTALLATION AT A HINGE
(EXAMPLE)
BONDED LIGHT SEAL INSTALLATION
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 舱门 DOORS 1(20)
