2.....….........…...................................…..........…......…........1
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-11-04
ALL ú ú 03 Page 406 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(2) This table is for the main entry door no. 5.
~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401| 2 |Guide arm assembly | 52-11-04 | 05 | 70 | | | 3 |Bolt | 52-11-09 | 04 | 702 | | | 4 |Washer | | | 705 | | | 5 |Upper hinge cover | | | 708 | | | 6 |Bolt | | | 699 | | | 7 |Bolt | | | 696 | | | 8 |Guide arm support fitting | 52-11-04 | 05 | 125 | | | 10 |Guide arm pin | | | 15 | | | 13 |Washer | | | 120 | | | 14 |Bolt | | | 115 | | | 22 |Washer | | | 60 | | | 23 |Nut | | | 65 | | | 24 |Bolt | | | 55 | | | 25 |Washer | | | 35 | | | 26 |Elbow pin | | | 30 | | | 27 |Spacer | | | 17 | | | 28 |Bolt | | | 5 | | | 30 |Nut | | | 25 | | | 31 |Bolt | | | 20 | | | 32 |Bushing | | | 40 | 2.....….........…...................................…..........…......…........1
C. References
(1)
AMM 51-31-01/201, Seals and Sealing
(2)
AMM 52-11-01/501, Main Entry Doors No. 1
(3)
AMM 52-11-02/401, Main Entry Door Lining and Insulation
(4)
AMM 52-11-09/501, Main Entry Door No. 5
D.
Access
(1)
Access Panel
831L Door - No. 1 Main Entry, LH
835L Door - No. 5 Main Entry, LH
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-11-04
ALL ú ú 03 Page 407 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
E. Prepare for Installation.
S 864-029
(1)
Close and latch the door.
S 214-031
(2)
Do a check of the door flushness (AMM 52-11-01/501 for Door 1, or AMM 52-11-09/501 for Door 5).
S 824-032
(3)
If the door flushness is not correct, adjust the latch fittings (AMM 52-11-01/501 for door 1; or AMM 52-11-09/501 for door 5).
S 214-009
(4)
Make sure that the lubrication fitting on the rod end (18) will be on the inboard side of the guide arm (2) when it is installed.
NOTE: This will let you easily get access for subsequent
____
lubrication.
S 824-010
(5)
If the position of the lubrication fitting is not correct, do these steps:
(a)
Turn the rod end (18) to put the lubrication fitting in the correct position.
(b)
Adjust the length of the guide arm (2).
