747-400 AMM 飞机维护手册起落架 LANDING GEAR 7(67)_航空信息_民用航空_通用航空

曝光台注意防骗网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

~............................................................ | CONNECTORS | | Right Body Gear Truck | .............................................................. | Wheel No. 9 | Wheel No. 10 | Wheel No. 11 | Wheel No. 12 | .............................................................. | DM56 | DM55 | DM57 | DM54 | 2...............…..............…..............…..............1
~............................................................ | CONNECTORS | | Right Wing Gear Truck | .............................................................. | Wheel No. 13 | Wheel No. 14 | Wheel No. 15 | Wheel No. 16 | .............................................................. | DM60 | DM59 | DM61 | DM58 | 2...............…..............…..............…..............1
2) Put the antiskid transducer assembly in position in the end of the axle. 3) Do the steps that follow to install the two lockbolts (3):
NOTE: The bolts must go through the slot in the axle
____ nut, the axle, and the transducer support. The direction that you install the bolts is optional.
a) Install the bolts (3).
b) If it is necessary, turn the rotor on the wheel
interface unit for access to install the lockbolts.
c) Install the washers (4) and the nuts (5).
d) Tighten the bolt to 75-85 pound-inches.
S 864-017
(2)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:

(a)
P180 DC Power Distribution Panel
1) 180J7, ANTI-SKID 1-3
2) 180J8, ANTI-SKID 14-16
3) 180F7, ANTI-SKID 2-4
4) 180F8, ANTI-SKID 13-15
5) 180J22, ANTI-SKID 5-7
6) 180J23, ANTI-SKID 10-12
7) 180F22, ANTI-SKID 6-8

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

32-42-04
ALL ú ú 03 Page 409 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
8) 180F23, ANTI-SKID 9-11
S 724-023
(3)
Do the Brake System BITE Test procedure in the "Ground Tests - Brake Control System" task (AMM 32-42-00/501).

S 724-018

(4)
Do these steps to do a test on the antiskid transducer:

WARNING:_______THIS TEST OPERATES THE BRAKES. MAKE SURE THAT THE AREA AROUND EACH BRAKE IS CLEAR AND THAT THERE ARE CHOCKS UNDER THE WHEELS. THIS WILL PREVENT INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(a)
Put chocks under the wheels.

(b)
Release the parking brake.

1) P6 Main Power Distribution Panel
a) 6L18, PARK BRAKE

WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL
_______ CONTROL SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(d)
Supply hydraulic pressure to hydraulic system No. 4
(AMM 29-11-00/201).

(e)
Set the parking brake.

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

32-42-04
ALL ú ú 03 Page 410 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(f)

(g)

A
747-400 MAINTENANCE MANUAL
Turn the antiskid transducer shaft at approximately 600 RPM and do these checks:
NOTE: Use the Spinup Equipment Tool if it is available.
____ When you perform the transducer spin test, both the locked wheel protection and skid protection functions are tested. Locked wheel protection continously compares the fore/aft (tandem) wheel speeds. A difference in wheel speeds of 30% will cause the brake pressure of the slower wheel to be released. For example, while you spin the transducer for wheel #1, the brake pressure for wheel #3 should release (the slower/stopped tandem wheel). The second part of the transducer spin test, stopping the spinning transducer quickly, testst the skid protection function. when the transduceris stopped quickly, the antiskid card senses this as a skid of the wheel and release that brake. For example, when the spinning transducer for wheel #1 is stopped quickly, the brake pressure for wheel #1 should release.
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册起落架 LANDING GEAR 7(67)