(2)
Lift the door (2).
(3)
Move the empty roll (5) from the right to the left to disengage it from its support (7).
(4)
Clean the remaining paper off the paper cutter (1).
(5)
Get a paper roll (5) from the flexible panel of the coat stowage, cockpit side. Remove the adhesive tape.
(6)
Install the new roll of paper (5) on its support (7).
NOTE : Make sure that the roll of paper turns correctly.
____
(7)
Manually engage the end of the paper under the drive roller (6). Pull the paper to the slot of the paper cutter (1) (in the direction shown on the self-adhesive labels).
NOTE : Make sure that paper is held tight.
____
(8)
Close the door (2).
(9)
Lock the door (2) with the locking system (3).
(10) Push the SLEW pushbutton switch (4) to move the paper out of the slot of the paper cutter (1).
1EFF : ALL 1 31-35-22Page 302 1 1 Feb 01/98 1 1 1CES 1
Printer
Figure 301/TASK 31-35-22-991-002
1EFF : ALL 1 31-35-22 Page 303
1 1 Feb 01/98
1 1
1CES 1
(11) Use the cutter to remove unwanted paper.
________
5. Close-up
Subtask 31-35-22-860-051
A. Put the aircraft back to its initial configuration.
(1)
De-energize the aircraft electrical circuits
(Ref. TASK 24-41-00-862-002)
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 31-35-22Page 304 1 1 Feb 01/98 1 1 1CES 1
PRINTER (4TW) - REMOVAL/INSTALLATION
____________________________________ TASK 31-35-22-000-001 Removal of the Printer (4TW)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 31-35-22-991-001 Fig. 401
3. Job Set-up
__________ Subtask 31-35-22-860-052
A. Energize the aircraft electrical circuits
(Ref. TASK 24-41-00-861-002)
Subtask 31-35-22-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU PTR/SPLY 6TW J21
1EFF : ALL 1 31-35-22Page 401 1 1 Feb 01/98 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 401/TASK 31-35-22-991-001) Subtask 31-35-22-020-050
A. Removal of the Printer
(1)
Loosen the four quarter-turn fasteners (1).
(2)
Remove the printer (2) from its housing (5).
(3)
Disconnect the connector (4) from the receptacle (3).
(4)
Remove the printer (2).
(5)
Put blanking caps on the electrical connectors (3) and (4).
1EFF : ALL 1 31-35-22Page 402 1 1 Feb 01/98 1 1 1CES 1
Printer
Figure 401/TASK 31-35-22-991-001
1EFF : ALL 1 31-35-22 Page 403
1 1 Feb 01/98
1 1
1CES 1
TASK 31-35-22-400-001 Installation of the Printer (4TW)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 31-35-00-710-001 Operational Test of the Printer
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM 指示/记录系统 3(8)
