R 1EFF : 106-149, 211-299, 301-399, 401-499, 1 31-36-00Page B23 1 1 Config-2 Aug 01/05 1 1 1CES 1 -----------------------------------------------------------------------------| Scratchpad Message | Reason | |------------------------|--------------------------------------------------| | OUT OF RANGE | - Negative Number | | | - Number > 999999 | -----------------------------------------------------------------------------
(c)
AIDS Dump Disk Status Information (Ref. Fig. 066) The Dump Disk Status Information menu page shows which SAR reports are dumped from the Solid State Mass Memory (SSMM). Display: The Dump Disk Status Information page indicates DISK TYPE (MANUALLY, AUTO, ONLINE or NONE), Number of REPORTS, Number of SAR files and the Number of TOTAL dumped items. Additional the Number of free Dump disk spaces in Bytes shows next to the BYTES LEFT indication.
(d)
AIDS Documentary Data (Ref. Fig. 067) The AIDS Documentary Data page displays data about Aircraft identification and AIDS software. Access:
-
Set AIDS on the MCDU main menu
-
Set REPROGRAMMING on the AIDS menu
-
Set DOC DATA on the AIDS : SPECIAL FUNC/REPROG menu. Display:
-
A/C TAIL-NO
-
A/C TYPE (Engine Type appended)
-ENG Type
-FLEET IDENT
-P/N (software)
-S/N (serial number)
-LOAD-EN.
(e) AIDS Report Inhibit (Ref. Fig. 068) The AIDS Report Inhibit menu allows to suppress or activate report generation. Access:
-
Set AIDS on the MCDU main menu
-
Set REPROGRAMMING on the AIDS menu
-Enter LINEMTCE or ENGINEER level user access password
-Set INHIBIT on the AIDS SPECIAL FUNC/REPROG menu
-Use the scroll arrows to get access to the next pages. Disable/Enable:
R 1EFF : 106-149, 211-299, 301-399, 401-499, 1 31-36-00Page B24 1 1 Config-2 Aug 01/05 1 1 1CES 1
AIDS - Dump Disk Status
Figure 066
R 1EFF : 106-149, 211-299, 301-399, 401-499, 1 31-36-00Page B25 1 1 Config-2 Aug 01/05 1 1 1CES 1
AIDS - Documentary Data
Figure 067
R 1EFF : 106-149, 211-299, 301-399, 401-499, 1 31-36-00Page B26 1 1 Config-2 Aug 01/05 1 1 1CES 1
AIDS - Report Inhibit
Figure 068
R 1EFF : 106-149, 211-299, 301-399, 401-499, 1 31-36-00Page B27 1 1 Config-2 Aug 01/05 1 1 1CES 1
R - Push the line key adjacent to ENABLE or DISABLE indication
R below the related report line.
Display:
On the multiple menu pages the available reports are displayed.
Below each displayed report line the enabled/disabled status
shows.
The indication ENABLED changes into DISABLED or DISABLED changes
into ENABLED after selection of the line select key.
(f) AIDS Report Constant Reprogramming
(Ref. Fig. 069)
Any constants of an AIDS report is changeable through the MCDU.
Access:
- Set AIDS on the MCDU main menu
- Set REPROGRAMMING on the AIDS menu
- Enter LINEMTCE or ENGINEER level user access password
- Set CONSTANTS on the AIDS SPECIAL FUNC/REPROG menu.
Enter/Change:
R
R - Enter the report number and push the line select key 1L to
R call-up the constants of the selected report.
R
R - Enter the new value and push the line select key adjacent to
R the constant to change the related constant value.
R
R - Push the CLR mode key and push the line select key adjacent to
R the constant to call-up the GSE programmed constant value.
Display:
Next to the selected REPORT indication the change - status shows:
R - CHANGED: NO displays that none of the listed constants of the
R selected report has been changed through MCDU (or ACARS)
R - CHANGED: YES displays that al least one of the listed constants
R of the selected report has been changed
R - CHANGED: --- displays that no MCDU programmable constants are
R defined
R
The green displayed values of constants (AI reserved constants or
inappropriate password) can not changed by the user.
All changed constants are marked with an exclamation mark (|).
If there is no programmable constants in the selected report the
message NO MCDU PROGRAMMABLE CONSTANTS shows.
Possible Scratchpad Messages:
R 1EFF : 106-149, 211-299, 301-399, 401-499, 1 31-36-00Page B28 1 1 Config-2 Aug 01/05 1 1 1CES 1 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM 指示/记录系统 3(109)
