曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1585 Kit - Rigging Pins, All Systems
(Part #: F70207-109, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
C. Location Zones
Zone Area
211 Flight Compartment - Left
212 Flight Compartment - Right
316 APU Compartment - Right
333 Left Horizontal Stabilizer - Rear Spar to Trailing Edge
343 Right Horizontal Stabilizer - Rear Spar to Trailing Edge
D. Access Panels
Number Name/Location
318BR Tailcone Access Door
333BB Horizontal Stabilizer, Access Panel, Trailing Edge
333CB Horizontal Stabilizer, Access Panel, Trailing Edge
333DB Horizontal Stabilizer, Access Panel, Trailing Edge
333EB Horizontal Stabilizer, Access Panel, Trailing Edge
343BB Horizontal Stabilizer, Access Panel - T.E. Area
343CB Horizontal Stabilizer, Access Panel - T.E. Area
343DB Horizontal Stabilizer, Access Panel - T.E. Area
343EB Horizontal Stabilizer, Access Panel - T.E. Area
E. Elevator Balance Panel Installation
(Figure 402)
SUBTASK 27-31-41-860-002
(1) Make sure that the pressure to the elevator hydraulic systems A and B is removed, do this task:
Elevator Balance Panels - Test, TASK 27-31-00-700-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-41
Page 408
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-31-41-420-001
(2) Install the idler hinge [18] (bays 2, 3, and 4):
NOTE: If you are installing new balance panel assemblies or seals, follow the instructions in
Figure 402 to apply anti-corrosion compound to the new parts. If you use the same
parts that you removed, you do not need to apply the compound.
(a) Install the bolts [3] and washers [4] that attach the hinge half [2] to the balance panel
support [1].
(b) Loosely install the bolts [7] and washers [8] to attach the flat seal [5] to the idler hinge [18].
(c) Make sure that the clearance between the flat seal [5] and the stabilizer trailing edge rib is
0.01 +0.06/-0.00 inch (0.25 +1.52/-0.00 millimeters).
(d) Tighten the bolts [7].
SUBTASK 27-31-41-420-002
(3) Install the balance panel [10]:
(a) Put and hold the balance panel [10] in its position.
(b) Loosely install the bolts [12] and washers [11] to attach the balance panel [10] and the
elevator hinge seal [9] to the elevator [6].
1) Carefully install the elevator hinge seal [9] between the elevator [6] and balance panel
[10].
2) Check to make sure that the gap between the balance panel [10] and the hinge half for
the elevator hinge seal [9] does not allow either of the following conditions:
a) pinching of the seal material
b) movement of the seal inboard or outboard
NOTE: The nominal design dimension for the gap between the balance panel [10] and
the hinge half for the elevator hinge seal [9] that meets this condition is
0.05 ±0.02 in. (1.3 ±0.5 mm).
(c) Tighten the bolts [12].
(d) Make sure that the idler hinge [18] is turned down from the balance panel support [1].
(e) Loosely install the bolts [13] and washers [14] to attach the balance panel [10] to the idler
hinge [18] and idler hinge seal [19].
(f) Manually move the elevator through the full range of travel.
1) Make sure the idler hinge seal [19] stays loose for all elevator positions.
(g) Tighten the bolts [13].
(h) Loosely install the bolts [15] and washers [16] to attach the bulb seals [17] to the balance
panel [10].
CAUTION: MAKE SURE THAT YOU ADJUST THE BULB SEALS CORRECTLY. IF THE BULB
SEALS ARE NOT ADJUSTED CORRECTLY, DAMAGE TO THE TRAILING EDGE
RIBS CAN OCCUR.
(i) Check to make sure that the clearance between the bulb seal [17] or bulb seal [22] and
stabilizer rib is 0.02 +/- 0.01 inch (0.51 +/- 0.25 millimeter).
(j) Check to make sure that the clearance between the bulb seal [17] or bulb seal [22] and the
aft end of the flat seal is 0.20 inch (5.1 millimeters).
1) If it is necessary, loosen the bolts [7] and adjust the flap seal [5] or flap seal [20] to get
the necessary clearance.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-41
Page 409
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(k) Tighten the bolts [15].
SUBTASK 27-31-41-080-001
(4) Remove rig pin E-5 of the rig pin kit, SPL-1585 from the aft control quadrant (Figure 401).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飞机维护手册3(69)
