• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-03-20 12:25来源:蓝天飞行翻译 作者:admin
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 G.  Set mode selector to OFF.
 H.  Remove electrical power if no longer required (Ref 24-22-00).
 I.  Remove main body gear locks.
 WARNING:_______REFER TO (32-00-30) FOR LOCK REMOVAL PROCEDURE. RAPID ACTION OF DOORS MAY INJURE PERSONNEL OR DAMAGE EQUIPMENT.
 EFFECTIVITY

 
 ALL  09 Page 406  Apr 25/9734-57-01
 ADF CONTROL PANEL - REMOVAL/INSTALLATION
________________________________________
 1.  General
_______
 A.  Both ADF control panels are mounted in the flight deck on the pilots' control stand. Each panel is mounted with four fasteners and has electrical connections via a cable connector at the rear of the unit.
 2.  Referenced Procedures
_____________________
 A.  24-22-00, Maintenance Practices (Apply Power)
 3.  Remove ADF Control Panel
________________________
 A.  Open ADF 1 AC, ADF 1 DC, ADF 2 AC, and ADF 2 DC circuit breakers on electronic circuit breaker panel P7 before removing panel.
 B.  Loosen fasteners on control panel, pull control panel out and remove cable connector.
 4.  Install ADF Control Panel
_________________________
 A.  Attach cable connector to control panel and secure panel in place with four fasteners.
 B.  Provide electrical power (Ref 24-22-00).
 C.  Select OFF position (if provided) on ADF control panel(s) at pilots control cabin, then close circuit breakers on electronic circuit breaker panel P7.
 D.  Check that panel lights are on.
 NOTE: Check that flight deck panel lights are bright.
____
 E.  Perform ADF system tests in Adjustment/Test section.
 F.  Select OFF, ANT, or ADF mode at ADF control panel(s), as required.
 G.  Remove electrical power if no longer required (Ref 24-22-00).
 EFFECTIVITY

 
 ALL  01 Page 401  Jan 25/7934-57-02
 ADF RECEIVER - REMOVAL/INSTALLATION
___________________________________
 1.  General
_______
 A.  Both receivers are mounted on the aft rack in the center fuselage electronic equipment center. RF inputs from the antenna are supplied to each receiver via two cable connectors on the front while electrical interface is provided via a rack connector at the rear of the unit.
 2.  Referenced Procedures
_____________________
 A.  24-22-00, Manual Power - Maintenance Practices (Apply Power)
 3.  Remove ADF Receiver
___________________
 A.  Open ADF 1 AC, ADF 1 DC, ADF 2 AC, and ADF 2 DC circuit breakers on electronic circuit breaker panel P7 before removing receiver.
 B.  Remove two cable connectors from front of receiver, loosen hold-down fastener and pull out receiver.
 4.  Install ADF Receiver
____________________
 A.  Provide electrical power. Refer to 24-22-00.
 B.  Slide receiver into rack and secure hold-down fastener on front. Attach two cable connectors to front of receiver.
 C.  Select OFF mode (if provided) on ADF control panel(s) in pilot's control cabin, then close ADF 1 AC, ADF 1 DC, ADF 2 AC, and ADF 2 DC circuit breakers on electronic circuit breaker panel P7. Reselect ON mode (if provided) at ADF control panel(s).
 D.  Select ANT mode at ADF control panel(s). Check ADF panel lights are on.
 NOTE: Check flight deck panel lights are on bright.
____
 (1)
Perform ADF system tests in Adjustment/Test section.

 (2)
Select OFF, ANT, or ADF mode at ADF control panel, as required.


 E. Remove electrical power if no longer required. Refer to 24-22-00.
 EFFECTIVITY

 
 ALL  01 Page 401  Jan 25/7934-57-03
 PERFORMANCE MANAGEMENT SYSTEM - DESCRIPTION AND OPERATION
_________________________________________________________
 1.  General (Fig. 1)
_______
 A.  The performance management system (PMS) provides both throttle and pitch control to attain and maintain required altitudes and speeds with the most efficient use of fuel for the selected climb, cruise or descent mode of operation. For example, during cruise the pitch control maintains the airplane altitude at the selected altitude, smooths out temporary speed changes and reduces throttle activity. The throttles are controlled during cruise to compensate for longer term effects on speed.
 B.  The performance management system (PMS) provides waypoint control over the inertial navigation system (INS) so that all waypoint data may be entered into the PMS rather than into the INS. The PMS stores distance measuring equipment (DME) station data in the PMS computer unit memory. This data is selected for a desired flight plan and is also used by the PMS to provide DME updated present position to the INS.
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:747飞机维护手册AMM CHAPTER 34 - NAVIGATION 第34章导航4(116)