(2)
On the panel 25VU make sure that the APU MASTER SW p/bsw is OFF.
R EFF : 001-049, 101-105, 107-107, 151-199, 49-26-54Page 401 201-210, Aug 01/05
CES
(3)
Put a warning notice in the cockpit to tell persons not to start the APU.
(4)
Make sure that hydraulic systems are depressurized
(Ref. TASK 29-00-00-864-001).
Subtask 49-26-54-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
Subtask 49-26-54-010-050
C. Get Access
(1)
Put the access platform in position below the APU access doors 315AL and 316AR.
(2)
Open the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-010-001).
(3)
Set the LIGHT control SW 11LJ to the ON position.
4. Procedure
_________ (Ref. Fig. 401/TASK 49-26-54-991-001) Subtask 49-26-54-020-050
A. Removal of the Air/Oil Separator Adapter
(1)
Put the CONTAINER 10 L(2 1/2 USGAL) to the position below the air/oil separator adapter (1)
(2)
Remove the bolts (2), the washers (3) and the air/oil separator (1).
(3)
Remove the seal (6), the shims (7) and the packings (4, 5) from the air/oil separator adapter (1).
(4)
Discard the packings (4, 5).
(5)
Make a record of the shim thickness for installation.
R EFF : 001-049, 101-105, 107-107, 151-199, 49-26-54Page 402 201-210, Aug 01/05
CES
Air/Oil Separator Adapter Figure 401/TASK 49-26-54-991-001
R EFF : 001-049, 101-105, 107-107, 151-199, 201-210, 49-26-54 Page 403 Aug 01/05
CES
TASK 49-26-54-400-001 Installation of the Air/Oil Separator Adapter
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific Torque Wrench : range 36.00 to 220.00 lbf.in
(0.40 to 2.60 m.daN)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 03-002 GB DEF-STAN 91-101 LUBRICATING OIL TURBINE ENGINE SYNT BASE (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
4 packing 49-26-09 01 -040 5 packing 49-26-09 01 -050
R EFF : 001-049, 101-105, 107-107, 151-199, 49-26-54Page 404 201-210, Aug 01/05
CES
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
the Ground Connector 49-00-00-860-008 APU Start by External Power (131-9(A)) 49-00-00-860-009 APU Shutdown by External Power (131-9(A)) 52-41-00-010-001 Open the APU Doors for Access 52-41-00-410-001 Close the APU Doors after Access 49-26-54-991-001 Fig. 401
3. Job Set-up
__________
Subtask 49-26-54-860-051
A. Aircraft Maintenance Configuration
(1)
Energize the ground service network
(Ref. TASK 24-42-00-861-001).
(2)
On the panel 25VU make sure that the APU MASTER SW p/bsw is OFF.
(3)
Make sure that there is a warning notice in the cockpit to tell persons not to start the APU.
(4)
Make sure that hydraulic systems are depressurized
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM 机载辅助动力 AIRBORNE AUXILIARY POWER4(7)
