(a) Close each circuit breaker that was opened when the colored light was removed.
S 864-009
(3) Set the switch to the on position.
(a) Make sure the light comes on correctly.
S 864-010
(4)
Set the switch to the off position.
S 414-008
(5)
Install the access panel with its screws.
TASK 33-43-11-024-015
4. White Steady Position Light - Removal (Fig. 401)
_____________________________________
A. References
(1)
SSM 33-40-03
(2)
WDM 33-43-01
B. Access
(1) Location Zone
301 Left Wing Tip
401 Right Wing Tip
C. Procedure
S 864-020
(1) Do one of these steps to remove electrical power from the steady position light:
(a) Open each applicable circuit breaker and attach the DO-NOT-CLOSE tag: 1) On the load control center panel, P18.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
33-43-11
ALL ú ú 03 Page 405 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(b) On the overhead panel, P5, set the switch to the off position and attach the DO-NOT-OPERATE tag.
S 024-016
(2) Remove the white light.
(a)
Remove the light mounting screws.
(b)
Carefully pull the white light aft and disconnect the electrical wires from the terminals.
TASK 33-43-11-424-017
5. White Steady Position Light - Installation (Fig. 401)__________________________________________
A. Consumable Materials
(1) A00230 Compound - Sealing and Insulation, BMS 537, Class B
B. References
(1)
AMM 24-22-00/201, Manual Control
(2)
AMM 33-43-11/201, Steady Position (Navigation) Lights
(3)
SSM 33-40-03
(4)
WDM 33-43-01
C. Access
(1) Location Zone
301 Left Wing Tip
401 Right Wing Tip
D. Light Installation
S 964-022
(1)
If it is necessary, replace the lamp (AMM 33-43-11/201).
S 424-018
(2)
Install the white light.
(a) Connect the electrical wires to the terminals.
WARNING: MAKE SURE YOU USE THE COMPOUND TO SEAL EACH BARE
_______ ELECTRICAL CONNECTION NEAR THE LIGHT. THIS WILL PREVENT AN EXPLOSION OF THE FUEL FUMES. AN EXPLOSION CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(b)
Apply a layer of the compound on the electrical terminals.
(c)
Push the light into the tube.
NOTE: Make sure the TOP mark on the lens retainer is up.
____
(d) Install the mounting screws.
E. Light Test
S 864-013
(1)
Supply electrical power (AMM 24-22-00/201).
S 864-012
(2)
Remove each DO-NOT-CLOSE or DO-NOT-OPERATE tag.
(a) Close each circuit breaker that was opened when the light was removed.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
33-43-11
ALL ú ú 01 Page 406 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 864-014
(3) Set the switch to the on position.
(a) Make sure the new lamp comes on correctly.
S 864-015
(4) Set the switch to the off position.
F. Light Test
S 864-016
(1)
Supply electrical power (AMM 24-22-00/201).
S 864-017
(2)
Remove each DO-NOT-CLOSE or DO-NOT-OPERATE tag.
(a) Close each circuit breaker that was opened when the light was removed.
S 864-018
(3)
Set the switch to the on position.
(a) Make sure the light comes on correctly.
(4)
Set the switch to the off position.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 灯 LIGHTS(79)
