(a) Apply SEALANTS (Material No. 09-018) to the bracket attach bolts
(6) and the nuts (7) and the flange attach bolts (12) and the nuts (13).
(3)
Install and tighten the bracket attach bolts (6) and the nuts (7).
(4)
Install and tighten the flange attach bolts (12) and the nuts (13).
(5)
Put the clamps (16) in position and install and tighten the bolts
(14) and the nuts (15).
(6)
Put the handles (11) in position and install the pins (9), the washers (10) and safety with new cotter pins (8) (8).
(7)
Connect the rigid control assembly (4) to the latch lever (5) with the pin (2), the spacers and space washers (3) and safety with a new cotter pin (1) (1).
**ON A/C 106-149, 210-299,
Subtask 25-62-43-420-051-A
A. Install the Rigid Control Assembly
(1)
Put the rigid control assembly (4) in position.
(2)
Apply the new sealant.
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(a) Apply SEALANTS (Material No. 09-018) to the bolts (6) and (12), the nuts (7) and (13) and the mating surface of the bracket (10).
(3) Install and tighten the bolts (6) and (12) and the nuts (7) and (13).
R EFF : 001-049, 051-099, 101-149, 151-199, 25-62-43Page 423 201-299, 401-499, Aug 01/05
CES
(4)
Put the clamps (16) in position and install and tighten the bolts
(14) and the nuts (15).
(5)
Attach the handles (11) to the aircraft structure with the burr-strip (9).
(6)
Connect the rigid control assembly (4) to the latch lever (5) with the pin (2), the spacers and space washers (3) and safety with a new cotter pin (1) (1).
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 25-62-43-820-051
B. Adjust the Release Mechanism
(1)
Move the latch lever (5) to the rear until it touches the latch lever bracket (21) at point 'A'.
(2)
Move the bellcrank (17) to the rear until it touches the latch lever stop-bolt at point 'B'.
(3)
Remove the lockwire from the spring strut adjust-nut (18).
(4)
Adjust the over-center spring strut (19) until the full dimension between the flanges of both end bushes (26) is 53.00 +0.5 -0.5 (2.09 +0.02 -0.02 in.).
(5)
Safety the spring strut adjust-nut (18) with lockwire MISCELLANEOUS (Material No. 19-010).
(6)
If necessary, adjust the rubber ice-protection bellows (25). Make sure that the bellows are correctly installed over the end bushes (26).
(7)
Remove the lockwire and turn the sleeve adjust nuts (20) until you get a clearance of 0.5 mm (0.02 in.) at point 'A'. Measure the clearance between the lip of the latch lever (5) and the top of the latch lever bracket (21).
(8)
Turn the sleeve adjust nuts (20) 5 full turns more in the direction to loosen the linkage of the rigid control assembly (4).
(9)
Safety the sleeve adjust nuts (20) with lockwire MISCELLANEOUS (Material No. 19-010).
R EFF : 001-049, 051-099, 101-149, 151-199, 25-62-43Page 424 201-299, 401-499, Aug 01/05
CES
(10)
Remove the lockwire and turn the adjust nuts of the connecting-rod
(22) until the release levers (23) touch the stops (24).
(11)
Measure the clearance between the latch lever stop-bolt and the bellcrank (17) at point 'B'. You must have a clearance of 0.3 +0.1 -0.1 mm (0.012 +0.004 -0.004 in.).
(12)
If the clearance is not in these limits, do steps (10) and (11) again.
(13)
Safety the adjust nuts of the connecting-rod (22) with lockwire MISCELLANEOUS (Material No. 19-010).
5. Close-up
________ Subtask 25-62-43-410-052
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the air conditioning duct (Ref. TASK 21-20-00-410-001).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备4(91)
