25-54-41-991-001-B Fig. 401B
EFF : ALL
25-54-41Page 401
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
**ON A/C 001-049, 051-099, 101-149, 201-299,
25-54-41-991-002 Fig. 402 R **ON A/C 151-199, 401-499,
25-54-41-991-002-A Fig. 402A
**ON A/C 301-399,
25-54-41-991-002-B Fig. 402B
**ON A/C ALL
3. Job Set-up
__________
Subtask 25-54-41-010-050
A. Get Access
(1)
Open the FWD cargo-compartment door and install the actuator safety lock (Ref. TASK 52-30-00-860-001).
(2)
Put the access platform in position at the opening of the FWD cargo-compartment door.
**ON A/C 062-099, 106-149, 203-299,
Subtask 25-54-41-865-050
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL SERVICE IDENT. LOCATION -------------------------------------------------------------------------------2000VU SEMI AUTO CLS-FWD 2MY B3 2000VU SEMI AUTO CLS-FWD 3MY B1
EFF : ALL
25-54-41Page 402
**ON A/C ALL
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 201-299,
Subtask 25-54-41-020-050
A. Removal of the Tie-Down and Net Attachment Fittings from the Floor Area (Ref. Fig. 401/TASK 25-54-41-991-001)
(1)
Remove the cargo net(s) (6), if installed:
(a)
Disconnect the net fittings (7) from the applicable net attachment fittings of the cargo-compartment floor and ceiling areas.
(b)
Remove the cargo net(s) (6).
(2)
Remove the tie-down points (2): NOTE : The removal procedure for all the tie-down points (2) is the
____ same. Therefore, the removal procedure for one tie-down point
(2) only is given here.
(a)
Remove the screws (1) from the tie-down point (2).
(b)
Remove the tie-down point (2) from the structure (3).
(3)
Remove the seat-track section (5):
(a)
Remove the screws (4) from the seat-track section (5).
(b)
Remove the seat-track section (5) from the structure (3).
(4)
Remove the tie-down points (9): NOTE : The removal procedure for all the tie-down points (9) is the
____ same. Therefore, the removal procedure for one tie-down point
(9) only is given here.
(a)
Remove the screws (8) from the tie-down point (9).
(b)
Remove the tie-down point (9) from the plug housing (10).
EFF : ALL
25-54-41Page 403
Tie-Down and Net Attachment Fittings - FWD Cargo-Compartment Floor Area Figure 401/TASK 25-54-41-991-001
R EFF : 001-049, 051-099, 101-149, 201-299, 25-54-41Page 404 May 01/05
CES
(c) If necessary, remove the plug housing (10) from the structure (3).
(5) Remove the tie-down fittings (12): NOTE : The removal procedure for all the tie-down fittings (12) is
____ the same. Therefore, the removal procedure for one tie-down fitting (12) only is given here.
(a)
Remove the screws (11) from the tie-down fitting (12).
(b)
Remove the tie-down fitting (12) from the structure (3).
(6)
Remove the tie-down fitting (14):
(a)
Remove the screws (13) from the tie-down fitting (14).
(b)
Remove the tie-down fitting (14) from the structure (3).
(7)
Remove the tie-down fittings (16): NOTE : The removal procedure for all the tie-down fittings (16) is
____ the same. Therefore, the removal procedure for one tie-down fitting (16) only is given here.
(a) Remove the screws (15) from the tie-down fitting (16).
(b) Remove the tie-down fitting (16) from the structure (3). R **ON A/C 151-199, 401-499,
Subtask 25-54-41-020-050-A
A. Removal of the Tie-Down and Net Attachment Fittings from the Floor Area (Ref. Fig. 401A/TASK 25-54-41-991-001-A)
(1) Remove the cargo net(s) (1), if installed:
(a)
Disconnect the net fittings (2) from the applicable net attachment fittings of the cargo-compartment floor and ceiling areas.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备4(11)
