(6)
Connect the connector (3) to the antenna (2).
(7)
Put the antenna (2) on the outer surface of the fuselage, and install the screws (1).
(8)
Tighten the screws (1) and TORQUE to between 0.40 and 0.50 m.daN
(35.39 and 44.24 lbf.in).
(9)
Remove unwanted sealant with a nonmetallic scraper.
(10)
Remove unwanted masking tape.
(11)
Clean the area: WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(a) Clean with CLEANING AGENTS (Material No. 11-003), and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003).
R EFF : 102-149, 151-199, 201-299, 301-399, 25-65-14Page 407 401-499, Aug 01/05
CES
(12) Make sure that the bonding resistance between the antenna (2), and the surface of the fuselage is not more than 5 milliohms (Ref. TASK 20-28-00-912-005).
**ON A/C 151-199, 211-228, 301-302,
Subtask 25-65-14-740-050
C. Do the BITE test (Ref. TASK 25-65-00-740-001).
R **ON A/C 102-149, 151-199, 201-299, 301-399, 401-499,
Subtask 25-65-14-370-050
D. Application and Curing of Sealants
(Ref. Fig. 401/TASK 25-65-14-991-001)
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(1) Apply materials:
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(a)
Apply a bead of SEALANTS (Material No. 09-016) around the bottom edge of the antenna (2) and on the heads of the screws (1).
(b)
Make a smooth contour of the sealant around the bottom edge of the antenna (2) and the heads of the screws (1).
(c)
Let the sealants cure.
R EFF : 102-149, 151-199, 201-299, 301-399, 25-65-14Page 408 401-499, Aug 01/05
CES
(d)
Apply STRUCTURE PAINTS (Material No. 16-021) on the sealant around the bottom edge of the antenna (2).
(e)
Apply PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-001B) on the sealant on the heads of the screws (1).
5. Close-up
________ Subtask 25-65-14-942-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R EFF : 102-149, 151-199, 201-299, 301-399, 25-65-14Page 409 401-499, Aug 01/05
CES CONTROL PANEL - REMOTE, AIRCRAFT EMERGENCY LOCATOR (111MX)
__________________________________________________________ REMOVAL/INSTALLATION
____________________ TASK 25-65-18-000-001 Remote-Control Panel (RCP) 111MX (Emergency Locator Transmitter) - Removal
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 25-65-18-991-001 Fig. 401
3. Job Set-up
__________ Subtask 25-65-18-861-050
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001).
4. Procedure
_________ Subtask 25-65-18-020-050
A. Removal of the RCP 111MX
(Ref. Fig. 401/TASK 25-65-18-991-001)
(1)
Hold the front face of the RCP (1) and loosen the captive screws (3).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备4(159)
