WARNING : MAKE SURE THAT THE LOCKPIN ASSEMBLY IS CORRECTLY INSTALLED
_______ IN THE VALVE/REGULATOR ASSEMBLY OF THE INFLATION RESERVOIR. IT PREVENTS AN ACCIDENTAL INFLATION OF THE ESCAPE SLIDE/SLIDE RAFT.
(8) Make sure that the door frame linings:
- of the LH FWD Emergency Exit Door, Zone 231 are removed (Ref. TASK 25-23-47-000-004).
- of the RH FWD Emergency Exit Door, Zone 232 are removed (Ref. TASK 25-23-47-000-009).
- of the LH AFT Emergency Exit Door, Zone 251 are removed (Ref. TASK 25-23-47-000-010).
- of the RH AFT Emergency Exit Door, Zone 252 are removed (Ref. TASK 25-23-47-000-010).
(9) Make sure that the RIGGING PIN - SLIDE RELEASE MECHANISM (55) is
installed in the related rigging hole of the lever assembly (54).
(10)
Make sure that the RIGGING PIN - SLIDE RELEASE MECHANISM (44) is installed in the related rigging hole of the release lever (43).
(11)
Make sure that the insulation blankets in the area that you are working, are removed (Ref. TASK 25-80-00-000-001).
EFF : 301-399, 25-62-48Page 421
Nov 01/04
R
CES 4. Procedure
_________
Subtask 25-62-48-210-053
A. Preparation for Installation
(1) Clean the component interface and/or the adjacent area:
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(a) Clean the component interface and/or the adjacent area with CLEANING AGENTS (Material No. 11-003) a clean cloth and a nonmetallic scraper.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
EFF : 301-399, 25-62-48Page 422
Nov 01/04
R
CES Subtask 25-62-48-420-051
B. Installation of the Emergency Escape-Slide Release-Mechanism Assembly (Ref. Fig. 403/TASK 25-62-48-991-003)
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(1) Apply special material on the threads of all screws:
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE
_______
SPECIAL MATERIAL.
THIS MATERIAL IS DANGEROUS.
WARNING : YOU MUST ALWAYS WEAR RUBBER GLOVES WHEN YOU DO THIS
_______
PROCEDURE.
(a) Apply SPECIAL MATERIALS (Material No. 05-002) on the threads of all screws, you use for the installation of the emergency escape-slide release-mechanism assembly.
(2) Install the bearing-assembly:
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE
_______
SPECIAL MATERIAL.
THIS MATERIAL IS DANGEROUS.
WARNING : YOU MUST ALWAYS WEAR RUBBER GLOVES WHEN YOU DO THIS
_______
PROCEDURE.
(a)
Apply SEALANTS (Material No. 09-019) on the mating surface of the bearing-assembly (6).
(b)
Put the bearing-assembly (6) in position and install the washers
(5) and the screws (4).
EFF : 301-399, 25-62-48Page 423
Nov 01/04
R
CES (3) Install the override clutch:
NOTE : There are punch marks located on the override clutch (14), on
____ the shaft (16) and on the lever (28) to make the installation procedure easier.
(a)
Apply COMMON GREASE (Material No. 04-004) on the shaft (16).
(b) 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备4(139)
