(c)
Move the latch lever rearward until it touches the lever bracket at POINT "A".
(d)
Move the double lever rearward until it touches the latch lever stop-bolt (2) at POINT "B".
(e)
Turn the adjusting-rod (3) and adjust the spring-rod assembly to
53.0 +0.5 -0.5 mm (2.0866 +0.0196 -0.0196 in.).
(f)
Tighten the lock-nut (1) of the eye-end fitting.
(g)
Safety the lock-nut (1) with MISCELLANEOUS (Material No. 19-010) (Ref. TASK 20-11-11-911-001).
(h)
Make sure that the rubber bellows of the over-center spring rod is in its correct position after you have done the adjustment.
(6)
Install the rigid control-cables: (Ref. Fig. 404/TASK 25-62-43-991-003)
(a)
Apply COMMON GREASE (Material No. 04-004) on the clevis-pin (4).
(b)
Put the rigid control-cables (1) together with the spacers (2) and (3), as recorded in the removal procedure, in position and install the clevis-pin (4).
(c)
Put the washer (5) in position and install the new cotter pin (6).
(7)
Adjust the distance between the latch lever and the lever bracket: (Ref. Fig. 409/TASK 25-62-43-991-008)
(a)
Cut, remove and discard the lock-wire from the lock-nuts (4) and the sleeve adjust-nuts (6) of the rigid control-cables (5).
(b)
Loosen the lock-nuts (4) of the rigid control-cables (5).
(c)
Turn the sleeve adjust-nuts (6) and adjust the distance between the latch lever and the lever bracket at POINT "A" to between 0.5 +0.1 -0.1 mm (0.0196 +0.0039 -0.0039 in.).
NOTE : Measure the distance, between the top of the lever bracket
____ and the lip of the latch lever with a feeler gage.
(d)
Loosen the sleeve adjust nuts (6) FIVE FULL TURNS.
(e)
Tighten the lock-nuts (4) of the rigid control-cables (5).
(f)
Safety the lock-nuts (4) and the sleeve adjust-nuts (6) with MISCELLANEOUS (Material No. 19-010) (Ref. TASK 20-11-11-911-001).
(8) Adjust the distance between the double lever and the latch lever: (Ref. Fig. 409/TASK 25-62-43-991-008)
(a)
Cut, remove and discard the lock-wire from the lock-nuts (7) of the tie-rod (8).
(b)
Loosen the lock-nuts (7) of the tie-rod (8).
(c)
Make sure that the release lever (14) touches the stop screw (15) at POINT "D" (see DETAIL "C")
(d)
Turn the tie-rod (8) clockwise or counterclockwise to adjust the distance between the double lever and the latch lever at POINT "B".
(e)
Adjust the distance between the double lever and the latch lever at POINT "B" to 0.3 +0.1 -0.1 mm (0.0118 +0.0039 -0.0039 in.).
NOTE : Measure the distance, between the double lever and the
____ latch lever stop-bolt (2) with a feeler gage.
(f)
Make sure that the eye-ends of the tie-rod (8) are in safety. NOTE : If you cannot push a needle or equivalent through the
____ inspection holes, the eye-ends are in safety.
(g)
Tighten the lock-nuts (7) of the tie-rod (8).
(h)
Safety the lock-nuts (7) with MISCELLANEOUS (Material No. 19-010) (Ref. TASK 20-11-11-911-001).
(9) Adjust the clearence between the release levers and the release pins of the emergency-exit hatches:
(Ref. Fig. 409/TASK 25-62-43-991-008)
(a)
Adjust the release lever of the AFT emergency-exit hatch:
(b)
Adjust the release lever of the FWD emergency-exit hatch: 1 Put the FWD emergency-exit hatch in the installed position
1_ Put the AFT emergency-exit hatch in the installed position
(Ref. TASK 52-21-11-400-001).
2_ Cut, remove and discard the lock-wire from the lock-nut (10)
of the setscrew (9).
3_ Loosen the lock-nut (10) of the setscrew (9).
4_ Make sure that the release pin of the emergency-exit hatch is
in the "ARMED" Position (see DETAIL "D").
5_ Make sure that the double lever touches the setscrew (9) at
POINT "C" (see DETAIL "A").
6_ Move the emergency-exit hatch until you can measure the
distance between the release lever (14) and the release pin
(16).
7_ Turn the setscrew (9) and adjust the distance between the
release lever (14) and the release pin (16) to 1.0 +0.5 -0.5
mm (0.0393 +0.0196 -0.0196 in.).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备4(102)
