(11)
Tighten the bracket attach nuts (15) and (16) and safety them with lockwire MISCELLANEOUS (Material No. 19-010).
Subtask 25-62-43-410-054
B. Preparation for Adjustment: WARNING : MAKE SURE THAT THE SAFETY/LOCK PIN IS CORRECTLY INSTALLED IN
_______ THE REGULATOR VALVE ASSEMBLY OF THE INFLATION RESERVOIR. THIS PREVENTS ACCIDENTAL:
-DISCHARGE OF THE INFLATION RESERVOIR
-DEPLOYMENT OF THE ESCAPE-SLIDE WHICH CAN CAUSE INJURY AND/OR DAMAGE.
(1)
In the passenger compartment:
(a) Install the emergency exit hatches and put them in the DISARMED/MANUAL position (Ref. TASK 52-21-11-400-001).
(2)
In the cargo compartment:
(a) Remove the cap and connect the TEST TOOL - RELEASE CABLE , ESCAPE SLIDE (TLW101) adapter to the flexible control assembly.
(3)
Set the test tool cursor to zero.
R EFF : 001-049, 051-099, 101-149, 151-199, 25-62-43Page 411 201-299, 401-499, Aug 01/05
CES
(4) Put the forward emergency exit hatch in the ARMED/AUTOMATIC position and remove the hatch (Ref. TASK 52-21-11-000-001).
NOTE : During the removal of the hatch the flexible control assembly
____ is operated when the latch pin moves the release lever.
(5)
Make sure that the test tool cursor has moved to show a minimum indication of 50.0 mm (1.97 in.).
(6)
If the test tool cursor shows less than the minimum indication, adjust the flexible control assembly as follows:
Subtask 25-62-43-820-050
C. Adjustment:
(1)
Make sure that the test tool cursor has moved to show a minimum indication of 50.0 mm (1.97 in.).
(2)
If the test tool cursor shows less than the minimum indication, adjust the flexible control assembly as follows:
(a)
Install the emergency exit hatch (Ref. TASK 52-21-11-400-001)
(b)
Adjust the conduit adjust nuts (7) and (8) on the flexible control assembly to make an adjustment of the conduit length,
(c)
Do steps 5.A.(3) and (4) and 5.B.(1) again.
(3)
Do steps 5.A (3) and (4) and 5.B.(1) and (2) with the rear emergency exit hatch.
(4)
Safety the flange attach bolt (9) to the conduit adjust nut (7) with lockwire MISCELLANEOUS (Material No. 19-010).
(5)
Safety the flange attach nut (11) to the conduit adjust nut (8) with lockwire MISCELLANEOUS (Material No. 19-010).
(6)
Remove the test tool from the flexible control assembly (1).
(7)
Connect the flexible control assembly (1) to the release cable assembly (21). Install the two collets and tighten the knurled sleeve nut (2).
R EFF : 001-049, 051-099, 101-149, 151-199, 25-62-43Page 412 201-299, 401-499, Aug 01/05
CES Subtask 25-62-43-710-050
D. Do this test: WARNING : MAKE SURE THAT THE SAFETY/LOCK PIN IS CORRECTLY INSTALLED IN
_______ THE REGULATOR VALVE ASSEMBLY OF THE INFLATION RESERVOIR. THIS PREVENTS ACCIDENTAL:
-DISCHARGE OF THE INFLATION RESERVOIR
-DEPLOYMENT OF THE ESCAPE-SLIDE WHICH CAN CAUSE INJURY AND/OR DAMAGE.
(1)
At the lower end of the release lever, try to lift the lever up with one finger. A strong resistance to lever movement shows that the joint between the flexible control assembly (1) and release cable assembly (21) is satisfactory.
(2)
A low resistance to lever movement shows that the cable joint is not correct. Loosen the knurled sleeve nut (2), remove the two collets and make the cable joint again. Do step A again.
(3)
Safety the knurled sleeve nut (2) with lockwirwe MISCELLANEOUS (Material No. 19-010).
5. Close-up
________ Subtask 25-62-43-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the air conditioning duct (Ref. TASK 21-20-00-410-001).
(3)
Install the emergency exit-frame linings (Ref. TASK 25-23-47-400-002).
(4)
Install the lower sidewall panel (Ref. TASK 25-23-44-400-001).
(5)
Install the upper sidewall panel (Ref. TASK 25-23-43-400-001).
(6)
Install the cove light panels (Ref. TASK 25-23-48-400-001).
(7)
Install the emergency exit hatches (Ref. TASK 52-21-11-400-001).
(8)
Install the passenger seats (Ref. TASK 25-21-41-400-001).
R EFF : 001-049, 051-099, 101-149, 151-199, 25-62-43Page 413 201-299, 401-499, Aug 01/05
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备4(88)
