(3)
Make sure that the area below the escape slide is clear.
(4)
Pull the quick release handle (1) up and release the escape slide assembly (3).
NOTE : When you pull the handle up, the handle, attached cable
____ assembly and parachute (release) pins will detach fully from the slide. You must retain the handle and its attached assembly.
(5)
Push in the flapper valves (4) of the aspirators (5) and release the pressure from the detached escape slide assembly (3).
(6)
Remove the blow out door (7) from the escape slide assembly (3). NOTE : The blow out door is attached to the escape slide assembly by
____
two straps with snap-fasteners.
(7)
Put the access platform in position at the escape-slide stowage compartment (6).
(8)
Remove the mooring line from the attach ring in the escape-slide stowage compartment (6).
NOTE : You can not see the mooring line until the escape slide
____ assembly (3) is released from the aircraft.
Escape-Slide - Inflated
Figure 401/TASK 25-62-47-991-002
EFF : 301-399, 25-62-47 Page 403
May 01/04
CES
(9) Roll up the deflated escape slide assembly (3). NOTE : When you roll up a deflated escape slide assembly, start from
____
the bottom end of the slide.
(10) Remove the escape-slide stowage compartment (6) (Ref. TASK 25-62-47-000-001).
NOTE : Make sure that you keep the stowage compartment (6), escape
____ slide (3), blow out door (7), the handle and its attached assembly (1) together. They are made to operate as a complete assembly from a specified door.
(11) Remove the empty inflation reservoir (Ref. TASK 25-62-49-000-001)
5. Close-up
________ Subtask 25-62-47-860-052
A. Aircraft Maintenance Configuration
(1)
Replace the diaphragm at the door damper and emergency operation cylinder (Ref. TASK 52-22-00-860-002).
(2)
Install a serviceable escape-slide enclosure (Ref. TASK 25-62-47-400-001).
(3)
Install a serviceable inflation reservoir (Ref. TASK 25-62-49-400-001).
TASK 25-62-47-000-001
Escape-Slide Enclosure - Removal
NOTE : The removal procedures are given for the escape-slide stowage
____ compartment installed below the left door 2; the procedures for compartments installed below the right door 2 and the left and right doors 3 are almost the same.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps No specific blanking plugs No specific warning notice No specific access platform 2 m (6 ft. 7 in.) 98A52107632000 1 PIN - SAFETY SLIDE 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-62-49-000-001 Inflation Reservoir, Escape-Slide - Removal 27-50-00-866-009 Retraction of the Flaps on the Ground 52-22-00-410-001 Closing of the Emergency Exit Doors from the
Passenger Compartment 52-22-00-410-002 Closing of the Emergency Exit Doors from the Outside 52-22-00-860-003 Special Precaution before Maintenance on the Door
Damper and Emergency Operation Cylinder 25-62-47-991-001 Fig. 402
3. Job Set-up
__________
Subtask 25-62-47-010-050
A. Get Access
WARNING : MAKE SURE THAT THE LOCKPIN ASSEMBLY IS CORRECTLY INSTALLED IN
_______ THE VALVE/REGULATOR ASSEMBLY OF THE INFLATION RESERVOIR. IT PREVENTS AN ACCIDENTAL INFLATION OF THE ESCAPE SLIDE/SLIDE RAFT.
(1)
Install the lockpin assembly in the operating head of the inflation reservoir (Ref. TASK 25-62-49-000-001).
(2)
Make sure that the EMER EXIT switch 4WL on the SIGNS panel 25VU is set to the OFF position (Ref. 23-73-00).
(3)
Put the operating striker lever of the door damper and emergency operation cylinder in the DISARMED position (Ref. TASK 52-22-00-860-003).
(4)
Make sure that the door is closed and locked (Ref. TASK 52-22-00-410-001) or (Ref. TASK 52-22-00-410-002).
(5)
Make sure that the slide control handle is in the DISARMED position and that the PIN - SAFETY SLIDE (98A52107632000) is installed .
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备4(132)
