8_ Tighten the lock-nut (10) of the setscrew (9).
9_ Safety the lock-nut (10) with MISCELLANEOUS (Material No. 19-
010) (Ref. TASK 20-11-11-911-001).
10__ Remove the AFT emergency-exit hatch.
_ (Ref. TASK 52-21-11-400-001).
2 If necessary loosen the bolt (19).
_ 3 Make sure that the release pin of the emergency-exit hatch is
_ in the "ARMED" Position (see DETAIL "D").
4 Make sure that the double lever touches the setscrew (9) at
_ POINT "C" (see DETAIL "A").
5 Move the emergency hatch until you can measure the distance
_ between the release lever (17) and the release pin (21).
6 Move the lever (20) to adjust the distance between the lever
_ (17) and the release pin (21) with a feeler gage to 1.0 +0.5 -0.5 mm (0.0393 +0.0196 -0.0196 in.).
7 Tighten the bolt (19).
_ 8 Safety the bolts (18) and (19) with MISCELLANEOUS (Material
_ No. 19-010) (Ref. TASK 20-11-11-911-001).
9 Remove the FWD emergency-exit hatch.
_
(10)
Connect the flexible control-cable: (Ref. Fig. 404/TASK 25-62-43-991-003)
(a)
Apply COMMON GREASE (Material No. 04-004) to the clevis-pin (9).
(b)
Put the flexible control-cable (11) together with the washers
(10) in position and install the clevis-pin (9).
(c)
Put the washer (8) in position and install the new cotter pin (7).
(11)
Adjust the flexible control-cable: (Ref. Fig. 409/TASK 25-62-43-991-008)
(a)
Cut, remove and discard the lock-wire from the lock-nuts (11) and the sleeve adjust-nuts (12) of the flexible control-cable (13).
(b)
Loosen the lock-nuts (11) of the flexible control-cable (13).
(c)
Turn the sleeve adjust-nut (12) and adjust the distance at the end of the flexible control-cable (13) to 11.5 +1.7 -1.7 mm (0.4527 +0.0669 -0.0669 in.).
NOTE : Measure the distance at the outer end of the flexible
____ control-cable (13) (see DETAIL "K") with a slide gage.
(d)
Do a check of the adjusted distance at the end of the flexible control-cable (13):
(e)
Tighten the lock-nuts (11) of the flexible control-cable (13).
(f)
Safety the lock-nuts (11) and the sleeve adjust-nut (12) with MISCELLANEOUS (Material No. 19-010) (Ref. TASK 20-11-11-911-001).
1_ Pull the end of the flexible control-assembly (13) three
times.
2_ Measure the distance at the end of the flexible control-cable
(13) with a slide gage.
3_ If the distance is not in the limits of 11.5 +1.7 -1.7 mm
(0.4527 +0.0669 -0.0669 in.), do the steps (c) thru (e) again.
(12) Adjust the cable-travel of the flexible control-cable: (Ref. Fig. 409/TASK 25-62-43-991-008)
(a)
Put the emergency-exit hatches in the installed position (Ref. TASK 52-21-11-400-001).
(b)
Install the TEST TOOL - RELEASE CABLE , ESCAPE SLIDE (TLW101) on the flexible control assembly (see DETAIL "L"):
1 Remove the protective plug and the two collets from the test
_ tool.
2_ Carefully engage the test tool into the related slot of the
flexible control-cable (13).
3_ Put the two collets in position, on the connection of the test
tool and the flexible control-assembly.
4_ Move the knurled sleeve-nut up and install it to the flexible
control-assembly.
(c)
Set the test tool cursor to zero.
(d)
Make sure that the release pin (16) of the FWD emergency-exit hatch is in the "ARMED" position (see DETAIL "D").
(e)
Make sure that the release lever (14) is in the "INACTIVATED" position (see DETAIL "C").
(f)
Open and remove the FWD emergency-exit hatch. NOTE : During the opening of the hatch, the release pin (16)
____ moves the release lever (14) and the flexible control-cable (13) is operated.
(g)
Make sure that the test-tool cursor has moved and shows a minimum cable-travel of 50.0 mm (1.9685 in.).
(h)
If the test-tool cursor shows less than the minimum cable-travel of 50.0 mm (1.9685 in.), you must adjust the flexible control-assembly.
(i)
Adjust the flexible control-assembly: 1 Put the emergency-exit hatches back in the installed position
_ (Ref. TASK 52-21-11-400-001).
2 Cut, remove and discard the lock-wire from the adjust nuts
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备4(103)
