12 Install the bush (144).
__
(b) Install the camshaft assembly: NOTE : You will find punch marks on the shaft-ends of the
____ camshaft assembly (121), and on the levers (113) and (127) to make the assembly easier.
1 Apply COMMON GREASE (Material No. 04-004) to the shaft-end
_
splines of the camshaft assembly (121).
2 Apply SEALANTS (Material No. 09-019) to the mating surfaces of
_
the bearing flanges (118) and (124).
3 Put the bearing flanges (118) and (124) in position on the
_
shaft-ends of the camshaft assembly (121).
4 Put the camshaft assembly (121) in position.
_
5_ Apply SPECIAL MATERIALS (Material No. 05-002) to the threads of the bolts (116) and (123), and on the thread of the stop-screw (115).
6_ Put the bearing flange (124) in position on the frame structure.
7_ Install the bolts (123) and the nuts (122).
8_ Put the bearing flange (118) in position on the frame structure.
9_ Install the bolts (116), the stop screw (115) and the nuts (117).
10__ Install the bolt (119) and the nut (120).
11__ Install the release-lever (127):
a_ Put the lever (130) in position on the release-lever (127).
b_ Install the screw (128) and the washer (129) but tighten the screw by hand only.
NOTE : The adjustment of the release-lever (127) is done____ after the complete installation of the emergency escape-slide release-mechanism.
c_ Apply COMMON GREASE (Material No. 04-004) to the splines of the release-lever (127).
d_ Install the release-lever (127) on the shaft-end of the camshaft assembly (121).
NOTE : The punch mark "C" on the release-lever (127) must____ align with the punch mark "D" on the shaft-end of the camshaft assembly (121).
e_ Install the bolt (125) and the washer (126).
12__ Install the release-lever (113):
a_ Apply COMMON GREASE (Material No. 04-004) to the splines of the release-lever (113).
b_ Put the spacer (114) in position on the shaft-end of the camshaft assembly (121).
c Install the release-lever (113) on the shaft-end of the
_
camshaft assembly (121).
NOTE : The punch mark "A" on the release-lever (113) must
____ align with the punch mark "B" on the shaft-end of the camshaft assembly (121).
d Install the washer (112) and the castellated nut (111).
_
e Install the new cotter pin (110).
_
(2) Install the release-mechanism lever assembly: (Ref. Fig. 407A/TASK 25-62-43-991-006-A)
(a) Assemble the lever assembly (83): 1 Apply COMMON GREASE (Material No. 04-004) to the bushes (102).
_ 2 Put the bushes (102) in position in the levers (100) and
_
(101).
3 Put the washers (96) and the bolts (95) together with the
_ washers (97) and the bushes (98) in position on the lever (100).
4 Put the lever (101) in position and install the nuts (99), but
_
do not tighten the nuts at this time.
5 Make sure that the levers (100) and (101) are aligned and
_
tighten the nuts (99).
6 Apply COMMON GREASE (Material No. 04-004) to the bushes (104).
_
7 Put the bushes (104) in position in the double lever (105).
_
8 Put the double lever (105) in its position between the levers
_
(100) and (101).
9 Adjust the lever assembly (83):
_ a Measure the distance between the double lever (105) and the
_ levers (100) and (101) with a feeler gage (see DETAIL "B").
b Make sure that the distance is not more than
_
0.9 mm (0.0354 in.).
c If the distance between the levers is not in this tolerance
_
adjust the distance with the washers (103).
(b) Assemble the release-mechanism lever assembly (82):
1 Install the setscrew (93), the locking device (92) and the nut
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备4(105)
