(m)
Carefully lift the door with the door control-handle (2).
(n)
Hold the door in this position, to prevent it to open fully.
(o)
Make sure that the girt bar (10) has engaged correctly in the floor fittings (26).
(p)
Carefully lower, and lock the door with the door control-handle (2).
(q)
Make sure that the girt bar (10) can move freely: 1 Move the emergency control-handle (3) from the ARMED to the
_
DISARMED position four times.
(r)
Set the emergency control-handle (3) to the DISARMED/MANUAL position, and install the SAFETY PIN - SLIDE ARMING (98D52103500000) (4).
(4) Examine the side of the pack-assembly (9) in flight direction: CAUTION : MAKE SURE THAT THE INFLATION CABLE IS NOT PULLED OUT FROM
_______ THE PACK-ASSEMBLY. IF IT IS PULLED OUT, DO NOT PUT IT BACK, BUT REPLACE THE PACK-ASSEMBLY. IF THE INFLATION CABLE IS PUT BACK INCORRECTLY, IT CAN PREVENT THE INFLATION OF THE ESCAPE-SLIDE RAFT.
(a) Make sure that the inflation cable (51) has not pulled out of the pocket (52), or is caught below the inflation reservoir.
R EFF : 003-049, 051-099, 101-149, 151-199, 25-62-44Page 459 201-299, 301-399, 401-499, Aug 01/05
CES
(5)
Remove the lock pin (18) from the regulator valve assembly (19):
(a)
Fold the wire cable (76) and wind the ORANGE flag (77) around the folded wire cable (76).
(b)
Put the folded lock pin (18) into the pocket (75).
(6)
Install the decorative-cover (20) on the pack-assembly (9):
NOTE : There are three different types of decorative-cover (20)
____ attachment:
-
Type 1, burr-strip.
-
Type 2, dual-lock re-closable fastener-strip.
-
Type 3, spring loaded latches.
The three different types are not interchangeable.
It is necessary to use more force, to attach the dual-lock
re-closable fastener-strip, than for burr-strip. You can hear
a continual click sound as the two halves are pushed together.
(a)
Types 1 and 2:
(b)
Type 3: 1 Engage the spring loaded bolts (73).
1_ Align the tongues on the under side of the top edge of the
decorative-cover (20) with the slots (17) on the packboard
(13).
2_ Press the top edge of the decorative-cover (20) on to the
attach-strips (16).
3_ Push the lower edge of the decorative-cover (20) against the
pack-assembly (9) until the spring clips engage.
_ 2 Push the lower edge of the decorative-cover (20) against the
_ pack-assembly (9) until the spring clips engage.
(c)
Carefully lift the door with the door control-handle (2).
(d)
Hold the door in this position, to prevent it to open fully.
(e)
Under the pack-assembly (9), engage the straps (21), between the decorative-cover (20) and the girt assembly (11).
R EFF : 003-049, 051-099, 101-149, 151-199, 25-62-44Page 460 201-299, 301-399, 401-499, Aug 01/05
CES R (f) Pull the straps (21) tight and put the loose ends around the R tight straps (21).
R NOTE : The ends of the straps (21) should not hang down loosely.
____ R
(g)
Carefully lower, and lock the door with the door control-handle (2).
(h)
Make sure that you can see the gage through the hole in the decorative-cover (20).
(7) Do a visual inspection of the visual indicator (30), and its related ARMED indication: (Ref. Fig. 406/TASK 25-62-44-991-017)
(a)
Remove the SAFETY PIN - SLIDE ARMING (98D52103500000) (4) and set the emergency control-handle (3) to the ARMED position.
(b)
If installed, make sure that the self-adhesive placards are in a good condition.
1 If necessary install new self-adhesive placards (Ref. TASK 11-
_ 00-00-400-007) and (Ref. AMM 11-32-52 P. Block 001).
2 Make sure that the point of the self-adhesive arrow (67),
_
aligns with the RED mark.
3 If not, re-position the self-adhesive arrow (67).
_
(c)
It is not necessary to make adjustments on aircraft where an ARMED placard (68) is installed on the cabin floor.
(d)
Set the emergency control-handle (3) to the DISARMED position, and install the SAFETY PIN - SLIDE ARMING (98D52103500000) (4).
(8) Do an installation check of the decorative-cover (20):
(a)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备4(123)
