(d)
Hold the escape-slide (7) with the mooring line (32).
(e)
Pull open the burr-strips of the girt assembly (11).
(f)
Pull the HANDLE (31).
(g)
Slowly release the mooring line (32):
-The girt lace-up joint (34) opens.
-And the girt assembly (11) releases from the girt bar (10).
(h) Carefully lower the escape-slide (7) to the ground. R NOTE : Two persons are necessary to hold the escape-slide (7),
____ R and help lower it to the ground.
(3)
Remove the girt bar (10) from the floor fittings (26):
(a)
Push the spring pawls (29) and pull the girt bar (10) inboard, from the floor fittings (26).
(b)
Remove the mooring line (32) from the girt bar (10).
(c)
Keep the girt bar (10) with the door.
(4)
Set the emergency control-handle (3) to the DISARMED/MANUAL position.
(5)
Release the safety barrier strap (8).
(6)
Lift the empty pack-assembly soft-cover (12) and close the door with the door control-handle (2) (Ref. TASK 52-10-00-410-001).
(7)
Remove the decorative-cover (20) from the pack-assembly (9):
R Escape-Slide - Inflated Figure 401/TASK 25-62-44-991-020- 12 (SHEET 1)
EFF : 001-002, 25-62-44 Page 404 Feb 01/02
CES
R Escape-Slide - Inflated Figure 401/TASK 25-62-44-991-020- 22 (SHEET 2)
EFF : 001-002, 25-62-44 Page 405 Feb 01/02
CES
Escape-Slide Raft - Inflated Figure 401A/TASK 25-62-44-991-020-A14 (SHEET 1)
R EFF : 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499, 25-62-44 Page 406 Aug 01/05
CES
Escape-Slide Raft - Inflated Figure 401A/TASK 25-62-44-991-020-A24 (SHEET 2)
R EFF : 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499, 25-62-44 Page 407 Aug 01/05
CES
Escape-Slide Raft - Inflated Figure 401A/TASK 25-62-44-991-020-A34 (SHEET 3)
R EFF : 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499, 25-62-44 Page 408 Aug 01/05
CES
Escape-Slide Raft - Inflated Figure 401A/TASK 25-62-44-991-020-A44 (SHEET 4)
R EFF : 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499, 25-62-44 Page 409 Aug 01/05
CES
NOTE : There are three different types of decorative-cover (20)
____ attachment:
-
Type 1, burr-strip.
-
Type 2, dual-lock reclosable fastener-strip.
-
Type 3, spring loaded latches.
The three different types are not interchangeable.
It is necessary to use more force, to pull apart dual-lock
reclosable fastener-strip, than for burr-strip. You can hear a
continual click sound as the two halves are pulled apart.
(a)
Types 1 and 2:
(b)
Type 3: 1 Pull the lower edge of the decorative-cover (20) away from the
1_ Pull the lower edge of the decorative-cover (20) away from the
pack-assembly (9), to disengage the spring clips.
2_ Carefully pull the top edge of the decorative-cover (20), from
the attach-strips (16), and remove it.
_ pack-assembly (9), to disengage the spring clips.
2 Disengage the spring loaded bolts (73) and remove the
_ decorative-cover (20).
(c) keep the decorative-cover (20) with the aircraft.
(8) Remove the pack-assembly (9) from the door:
(a)
Hold the pack-assembly (9).
(b)
Remove the bolts (24) and the washers (25), and keep them with the aircraft.
(c)
Let the pack-assembly (9) fall inboard on the supports (14), and continue to hold it.
(d)
Disconnect the electrical connector (15):
-
FOR 7500MM 2871VC-A.
-
FOR 7501MM 2870VC-A.
-
FOR 7502MM 2873VC-A.
EFF : 001-002, 25-62-44Page 410
May 01/02
R
CES
