__ a Put the lever (130) in position on the release-lever (127).
_ b Install the screw (128) and the washer (129) but tighten
_
the screw by hand only.
NOTE : The adjustment of the release-lever (127) is done
____ after the complete installation of the emergency escape-slide release-mechanism assembly.
c Apply COMMON GREASE (Material No. 04-004) to the splines of
_
the release-lever (127).
d Install the release-lever (127) on the shaft-end of the
_
camshaft assembly (121).
NOTE : The punch mark "C" on the release-lever (127) must
____ align with the punch mark "D" on the shaft-end of the camshaft assembly (121).
e Install the bolt (125) and the washer (126).
_
12 Install the release-lever (113):
__ a Apply COMMON GREASE (Material No. 04-004) to the splines of
_
the release-lever (113).
b Put the spacer (114) in position on the shaft-end of the
_
camshaft assembly (121).
c Install the release-lever (113) on the shaft-end of the
_
camshaft assembly (121).
NOTE : The punch mark "A" on the release-lever (113) must
____ align with the punch mark "B" on the shaft-end of the camshaft assembly (121).
d Install the washer (112) and the castellated nut (111).
_
e Install the new cotter pin (110).
_
(2) Install the release-mechanism lever assembly: (Ref. Fig. 407/TASK 25-62-43-991-006)
(a) Assemble the lever assembly (83): 1 Apply COMMON GREASE (Material No. 04-004) to the bushes (102).
_ 2 Put the bushes (102) in position in the levers (100) and
_
(101).
3 Put the washers (96) and the bolts (95) together with the
_ washers (97) and the bushes (98) in position on the lever (100).
4 Put the lever (101) in position and install the nuts (99), but
_
do not tighten the nuts at this time.
5 Make sure that the levers (100) and (101) are aligned and
_
tighten the nuts (99).
6 Apply COMMON GREASE (Material No. 04-004) to the bushes (104).
_
7 Put the bushes (104) in position in the double lever (105).
_
8 Put the double lever (105) in its position between the levers
_
(100) and (101).
9 Adjust the lever assembly (83):
_ a Measure the distance between the double lever (105) and the
_ levers (100) and (101) with a feeler gage (see DETAIL "B").
b Make sure that the distance is not more than
_
0.9 mm (0.0354 in.). c If the distance between the levers is not in this tolerance
_
adjust the distance with the washers (103).
(b) Assemble the release-mechanism lever assembly (82): 1 Install the setscrew (93), the locking device (92) and the nut
_
(91).
2 Apply COMMON GREASE (Material No. 04-004) to the bushes (89)
_
and (90).
3 Put the bushes (89) and (90) in position in the lever bracket
_
(94) as recorded in the removal procedure. 4 Apply COMMON GREASE (Material No. 04-004) to the bolt (88).
_ 5 Put the lever assembly (83) in position in the lever bracket
_ (94) and install the bolt (88).
6 Adjust the release-mechanism lever assembly (82):
_ a Measure the distance between the lever assembly (83) and
_ the lever bracket (94) with a feeler gage (see DETAIL "B").
b Make sure that the distance is not more than
_
0.9 mm (0.0354 in.). c If the distance between the levers is not in this tolerance
_ adjust the distance with the washers (84).
d Remove the bolt (88) and install the washers (84) as
_
necessary.
7 Install the bolt (88), the washer (87) and the castellated nut
_
(86).
8 TORQUE the castellated nut (86) to between 0.30 and 0.35 m.daN
_ (26.54 and 30.97 lbf.in) and install the new cotter pin (85).
(c)
Apply SEALANTS (Material No. 09-019) to the mating surface of the release-mechanism lever assembly (82).
(d)
Apply SPECIAL MATERIALS (Material No. 05-002) to the threads of the bolts (80).
(e)
Put the release-mechanism lever assembly (82) in position and install the bolts (80) and the nuts (81).
(3)
Install the release-mechanism tie-rod assembly: (Ref. Fig. 406/TASK 25-62-43-991-005)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备4(100)
