(3)
Remove the cover (5).
(4)
Release the quick change (7).
(a)
Pull the lever (8) and turn it to the vertical position.
(b)
Move the lever (8) to the open position.
(5) Lift the doghouse (1) free of the seat tracks (10) and remove it . **ON A/C 201-210,
Subtask 25-27-46-020-054-A
A. Removal of the doghouse 6600MM and 6601MM. R (Ref. Fig. 403/TASK 25-27-46-991-007)
(1)
Remove the drawer from the doghouse:
(a)
Make sure that the drawer lock (6) is unlocked.
(b)
Release the drawer latch (7) and pull the drawer (8) until it stops.
(c)
Remove the screws (5).
(d)
Disengage the drawer (8) from the guide rail (9) and remove it.
(2)
Remove the cover (11).
(3)
Remove the doghouse:
(a)
Pull the lever (2) and move it to the vertical position.
(b)
Move the lever (2) to the unlocked position.
(c)
Lift the doghouse (1) with the fittings (3) away from the seat tracks (4) and remove it.
R Doghouse Floor Mounted Figure 403/TASK 25-27-46-991-007
R EFF : 201-210, 25-27-46 Page 413 Feb 01/05
CES
**ON A/C 151-199, 201-210,
TASK 25-27-46-400-004
Installation of a Doghouse AFT
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
SYNTH.ESTER BASED GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 11-003 USA ASTM D 740
METHYL-ETHYL-KETONE (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
11-00-00-400-007 Installation of the ESSO (Scotchcal Labels) 24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from
the External Power
25-21-41-400-001 Installation of the Passenger Seats
AMM 11-32-25 P.Block 001 INTERIOR PLACARDS (SEE ALSO 11-42-25)
R **ON A/C 201-210,
R 25-27-46-991-007 Fig. 403 **ON A/C 151-199, 201-210,
3. Job Set-up
__________
Subtask 25-27-46-861-054
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001).
Subtask 25-27-46-860-053
B. Aircraft Maintenance Configuration
(1) Make sure that the doghouse is empty.
4. Procedure
_________
Subtask 25-27-46-210-051
A. Preparation for Installation
(1) Clean the seat tracks.
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(a) Clean the seat tracks with CLEANING AGENTS (Material No. 11-003), a cloth MISCELLANEOUS (Material No. 19-003).
(2) Clean the component interface and/or the adjacent area.
EFF : 151-199, 201-210, 25-27-46Page 416
Feb 01/05
R
CES
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Make sure that the parts retained from the removed component are clean and in the correct condition.
**ON A/C 151-199,
Subtask 25-27-46-420-053
B. Installation of the Doghouse 6600MM
(1)
Apply COMMON GREASE (Material No. 04-004) to the seat track fittings (9).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备2(97)
