EFF : ALL
25-28-42Page 458
May 01/04
R (d) Unwind 100 mm (3.9370 in.) of the new self-adhesive film (2) from
R the roll and remove the protective paper.
R (e) Align the self-adhesive film (2) to the NTF (1) and install it
R with a soft cotton cloth MISCELLANEOUS (Material No. 19-003) and
R a light pressure of your hand. Work from the middle of the
R self-adhesive film (2) towards the sides.
R (f) With a ROLLER - RUBBER press down the self-adhesive film (2) onto
R the NTF (1).
R NOTE : Move the rubber roller backwards and forwards and around____
R the edges for a better bond.
R (g) Do the steps (2)(d) thru (f) until you have installed all of the
R NTF (1) with the self-adhesive film (2).
R (3) Installation of the NTF to the GFRP:
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE_______
R THIS/THESE MATERIAL/S.
R USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
R (a) Clean the component interface and/or the adjacent area. Use
R CLEANING AGENTS (Material No. 11-004).
R (b) Do a visual inspection of the component interface and/or the
R adjacent area.
R (c) On the installation side of the NTF-covering (1) remove 100 mm
R (3.9370 in.) protective paper from the self-adhesive film (2).
R (d) Align the NTF (1) with the GFRP (5) and install it with a ROLLER-
R RUBBER.
R NOTE : Move the rubber roller backwards and forwards and around____
R the edges for a better bond.
R (e) Do the steps (3)(c) thru (d) until you have installed all of the
R NTF (1) to the GFRP (5).
R (4) Installation of the self-adhesive Film BONDING AND ADHESIVE COMPOUNDS
R (Material No. 08-082) (2) to the GFRP (5):
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE_______
R THIS/THESE MATERIAL/S.
R USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
EFF : ALL
25-28-42Page 459
R (a) Clean the component interface and/or the adjacent area.
R Use CLEANING AGENTS (Material No. 11-004).
R (b) Do a visual inspection of the component interface and/or the
R adjacent area.
R (c) Unwind 100 mm (3.9370 in.) of the new self-adhesive film from the
R roll and remove the protective paper.
R (d) Align the self-adhesive film (2) to the GFRP (5) and install it
R with a soft cotton cloth MISCELLANEOUS (Material No. 19-003) and
R a light pressure of your hand. Work from the middle of the
R self-adhesive film (2) towards the sides.
R (e) With a ROLLER - RUBBER press down the self-adhesive film (2) onto
R the GFRP (5).
R NOTE : Move the rubber roller backwards and forwards and around____
R the edges for a better bond.
R (f) Do the steps (4)(c) thru (e) until you have installed all of the
R GFRP (5) with the adhesive film (2).
R Subtask 25-28-42-160-056
R D. Preparation of the Seat Tracks and the Floor Panels for the Installation
R of the NTF-Covering.
R (Ref. Fig. 403/TASK 25-28-42-991-011, 404/TASK 25-28-42-991-012)
R WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK_______
R AREA WHEN YOU USE SPECIAL MATERIALS.
R IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH
R OR IN YOUR EYES :
R -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15
R MINUTES.
R -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS.
R DO NOT BREATHE THE FUMES FROM THE MATERIAL.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备2(119)
