(2)
Install the escape slide/escape slide (raft)
FOR 831AZ, 841AZ
install (Ref. TASK 25-62-44-400-001).
(3)
Do the special precautions after work on the doors (Ref. TASK 52-10-00-410-001).
Subtask 25-23-46-865-054
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15WN, 13WN, 48WV.
Subtask 25-23-46-862-050
C. De-energize the ground service network
(Ref. TASK 24-42-00-862-001)
EFF : ALL
25-23-46Page 411
Nov 01/00
R
CES
TASK 25-23-46-000-002
Removal of the Door Linings at the AFT Passenger/Crew Doors
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External
Power
52-10-00-010-001 Opening of the Passenger/Crew Door
25-23-46-991-002 Fig. 402
FOR FIN 832AZ, 842AZ
R 25-62-44-000-002 Removal of the Escape-Slide Pack-Assembly
3. Job Set-up
__________
Subtask 25-23-46-861-051
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001)
Subtask 25-23-46-010-053
B. Get Access
(1)
Open the passenger/crew door 832 (842) (Ref. TASK 52-10-00-010-001).
(2)
Remove the cabin escape facilities: FOR 832AZ, 842AZ remove the escape slide/raft (Ref. TASK 25-62-44-000-002)
EFF : ALL
25-23-46Page 412
Subtask 25-23-46-865-052
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
4. Procedure
_________
WARNING : MAKE SURE THE PERCUSSION LEVER OF THE DOOR DAMPER CYLINDER IS IN
_______
THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
Subtask 25-23-46-020-051
A. Remove the liningss R (Ref. Fig. 402/TASK 25-23-46-991-002)
(1)
Remove the lining 832FZ (842FZ) (8)
(a)
Remove the screws (26) the washers (25) and the grip (27).
(b)
Remove the screws (4) and the washers (3).
(c)
Loosen the screws (4) and turn the brackets.
(d)
Carefully release the lining (8) and remove it.
(2)
Remove the lining 832GZ (842GZ) (9)
(a)
Disconnect the rod (7) from the lining (9).
(b)
Remove and discard the cotter pin (6).
(c)
Remove the pin (5).
(d)
Remove the lining (9).
(3)
Remove the lining 832EZ (842EZ) (2)
(a)
Remove the screws (4) and the washers (3).
(b)
Release the lining (2) from the yo-yo rolls and remove it.
EFF : ALL
25-23-46Page 413
Door Linings - AFT Passenger/Crew Doors Figure 402/TASK 25-23-46-991-002- 13 (SHEET 1)
R EFF : CES ALL 25-23-46 Page 414 May 01/03
Door Linings - AFT Passenger/Crew Doors Figure 402/TASK 25-23-46-991-002- 23 (SHEET 2)
R EFF : CES ALL 25-23-46 Page 415 May 01/03
Door Linings - AFT Passenger/Crew Doors Figure 402/TASK 25-23-46-991-002- 33 (SHEET 3)
R EFF : CES ALL 25-23-46 Page 416 May 01/03
(4) Remove the handgrip and the lining 832DZ (832DZ) (20) CAUTION : DO NOT USE TOO MUCH FORCE WHEN YOU REMOVE THE COVER AS THIS
_______
CAN CAUSE DAMAGE TO THE RETAINER.
(a)
Carefully push the lugs (28) of the handgrip cover (22) with your finger in the direction of the arrows and remove the handgrip cover (22).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备2(33)
