(b)
Remove the screws (17) and (23), the washers (18) and the
handgrip (24).
(c)
Remove the spacer (19) and the lining (20).
(5)
Remove the lining 832DZ (842DZ) (21)
(a)
Remove the screws (4) and the washers (3).
(b)
Release the lining (21) from the yo-yo rolls and remove it.
(6)
Remove the lining 832CZ (842CZ) (1)
(a)
Remove the nut (12), the washer (13), the screw (15) and the handle plate (14) from the emergency control handle (16).
(b)
Remove the screws (4) and the washers (3).
(c)
Release the lining (1) from the yo-yo rolls and remove it.
(7)
Remove the lining 832BZ (842BZ) (10)
(a)
Remove the screws (4) and the washers (3).
(b)
Release the lining (10) from the yo-yo rolls and remove it.
(8)
Remove the lining 832AZ (842AZ) (11)
(a)
Remove the screws (4) and the washers (3).
(b)
Release the lining (11) from the yo-yo rolls and remove it.
TASK 25-23-46-400-002
Installation of the Door Linings at the AFT Passenger/Crew Doors
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
B. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
6 cotter pin 25-23-04 01 -260 6 cotter pin 25-23-04 01A-260 6 cotter pin 25-23-04 01B-260 6 cotter pin 25-23-04 01C-260 6 cotter pin 25-23-04 01D-260
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
11-00-00-400-002 Installation of the Decals 24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from
the External Power
AMM 11-32-25 P.Block 001 INTERIOR PLACARDS (SEE ALSO 11-42-25)
25-23-46-991-002 Fig. 402
FOR FIN 832AZ, 842AZ
R 25-62-44-400-001 Installation of the Escape-Slide Pack-Assembly
EFF : ALL
25-23-46Page 418
3. Job Set-up
__________ Subtask 25-23-46-860-052
A. Aircraft Maintenance Configuration
(1)
Make sure that the ground service network is energized
(Ref. TASK 24-42-00-861-001)
(2)
Clean the component interface and/or the adjacent area.
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Make sure that the parts retained from the removed component are clean and in the correct condition.
Subtask 25-23-46-865-053
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
4. Procedure
_________
WARNING : MAKE SURE THE PERCUSSION LEVER OF THE DOOR DAMPER CYLINDER IS IN
_______
THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
Subtask 25-23-46-420-051
A. Installation of the linings:
(Ref. Fig. 402/TASK 25-23-46-991-002)
(1) Install the lining 832AZ (842AZ) (11)
(a) Engage the lining (11) to the yo-yo rolls and install the washers
(3) and the screws (4).
EFF : ALL
25-23-46Page 419
May 01/03
R
CES
INTENTIONALLY BLANK
(2) Install the linings 832BZ (842BZ) (10) and 832DZ (842DZ) (21)
(a) Engage the linings (10) and (21) to the yo-yo rolls and install the washers (3) and the screws (4).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备2(34)
