(b)
Put the guide rail (5) in position and install the screws (4).
(c)
Install the grip (6).
(d)
Apply LUBRICANTS (Material No. 06-002) to the bracket (14).
(e)
Install the bracket (14). 1 Make sure that the nut (11) ,the spring-washer (12) and the
1_ Put the damper assembly (10)in position.
2_ Make sure that the grip (6) is in the correct position and
install it through the hole in the guide rail (5) and the
damper assembly (10).
3_ Install the spring (8) and the washer (9).
4_ Put the grip (6) through the other hole in the damper assembly
(10) and the bracket (5).
5_ Compress the spring (8) with the washer (9) and install a new
spring pin (7).
_ washer (13) are in position.
2 Put the bracket (14) into the guide rail (21).
_ 3 Put the threaded rod of the damper assembly through the hole
_ in the bracket (14).
4 Install the washer (17) ,the spring-washer (16) and the nut
_ (15).
5 Make sure that the dimension 'X' is 38 mm (1.4960 in.).
_
(f) Put the bracket (3) in position and install the washers (2) and the screws (1).
R **ON A/C 001-049, 101-105, 151-199,
Subtask 25-26-43-420-053-A
R B. Install the Center Class Divider 6388MM (Ref. Fig. 403/TASK 25-26-43-991-004-A) (1) Make sure that the class divider is in the removal position. (2) Put the class divider (1) in position. (3) Push the class divider (1) onto the divider rail (7). (4) Push the class divider (1) near its position. (5) Push the class divider (1) by the handles (3) outboard untill it engages. (6) Install the screws (4) the washers (5) and the stoppers.
R **ON A/C 051-052, 301-399,
Subtask 25-26-43-420-053-C
B. Install the Center Class Divider.
R **ON A/C 051-052,
R R (Ref. Fig. 403A/TASK 25-26-43-991-004) **ON A/C 301-399,
R (Ref. Fig. 403B/TASK 25-26-43-991-004-B) **ON A/C 051-052, 301-399,
(1) Put the class divider (1) with the attachment strips (4) in position (3). (2) Turn and Lower the lever (2) to attach the class divider (1).
CES CES
R **ON A/C 201-210,
R Subtask 25-26-43-420-053-B
R R R R R R R R R B. Install the Center Class Divider 6388MM (Ref. Fig. 403A/TASK 25-26-43-991-004) (1) Make sure that the class divider (1) is in the removal position. (2) Put the class divider (1) in position. (3) Push the class divider (1) onto the divider rail (2). (4) Push the class divider (1) near its position. (5) Push the lever (5) in the lock position untill its engage. (6) Install the screws (4) the nuts (3). **ON A/C 001-049, 101-105, 151-199, 201-210, 301-399,
Subtask 25-26-43-210-051
C. Make sure that the placards 'CURTAIN MUST BE OPEN DURING TAKE OFF AND LANDING' are installed on each side of the center class divider.
R **ON A/C 001-049, 051-052, 101-105, 151-199, 201-210, 301-399,
5. Close-up________ **ON A/C 301-399,
Subtask 25-26-43-410-067
A. Close Access
(1) Install the curtains on the center class divider (Ref. TASK 25-26-41-400-013).
R **ON A/C 001-049, 101-105, 151-199, 201-210, 301-399, Subtask 25-26-43-862-053
B. De-energize the ground service network (Ref. TASK 24-42-00-862-001).
R EFF : 001-049, 101-105, 151-199, 201-210, 25-26-43Page 422 301-399, May 01/05
CES
R **ON A/C 001-049, 051-052, 101-105, 151-199, 301-399,
TASK 25-26-43-000-012
Removal of the MCD Rail System
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External
Power
25-26-43-000-004 Removal of the Center Class Divider
25-26-43-991-014 Fig. 405
3. Job Set-up
__________
Subtask 25-26-43-861-058
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001)
Subtask 25-26-43-010-068
B. Get Access
(1) Remove the center class divider. (Ref. TASK 25-26-43-000-004)
R EFF : 001-049, 051-052, 101-105, 151-199, 25-26-43Page 423 301-399, May 01/05
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备2(79)
