WARNING : MAKE SURE THE PERCUSSION LEVER OF THE DOOR DAMPER CYLINDER IS
_______ IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Put the door lining (4) in position, engage the attach brackets to the yo-yo rolls and attach it with the screws (14).
(3)
Install the screws (10) and the washers (11).
Subtask 25-23-47-420-112
B. Installation of the Door Lining 833GZ (3)
(Ref. Fig. 402/TASK 25-23-47-991-014)
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Put the door lining (3) in position and attach it with the screws (12), (16), (20), the washers (15), (19), the nut (13) and the bracket (24).
NOTE : Install the screws, the washers, the nuts and the bracket as
____
identified during the removal procedure.
Subtask 25-23-47-420-113
C. Installation of the Door Lining 833DZ (6)
(Ref. Fig. 402/TASK 25-23-47-991-014)
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Put the door lining (6) in position and engage the attach brackets to the yo-yo rolls.
(3)
Install the LWR handle section (25) with the screws (28) and the washers (27).
(4)
Install the cover (26) to the LWR handle section (25). NOTE : Make sure that the lugs (29) of the cover (26) engage
____
correctly and you hear a click.
(5) Install the cover (21) the screws (22) and the washers (23). Subtask 25-23-47-420-114
D. Installation of the Door Lining 833CZ (2)
(Ref. Fig. 402/TASK 25-23-47-991-014)
(1)
Install the slide arm indicator light (Ref. TASK 52-73-21-400-003)
(2)
Install the cabin pressure light panel (Ref. TASK 52-73-22-400-003)
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
(4)
Put the door lining (2) in position and attach it with the screws
(32) the plugs (33), the screws (10) and the washers (11).
(5)
Lift up the cover (30) and install the plate (31) the screw (12) and the nut (13).
Subtask 25-23-47-420-115
E. Installation of the Door Lining 833EZ (7)
(Ref. Fig. 402/TASK 25-23-47-991-014)
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Put the door lining (7) in position and attach it with the screws
(10) and the washers (11). Subtask 25-23-47-420-116
F. Installation of the Door Lining 833JZ (1)
(Ref. Fig. 402/TASK 25-23-47-991-014)
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Put the door lining in position and attach it with the screws (8) and the washers (9).
Subtask 25-23-47-210-074
G. Visual Inspection
(1)
Make sure that all placards of the retained/new components are in the correct position and in good condition.
(2)
If necessary install the new placards, refer to (Ref. TASK 11-00-00-400-002) (Ref. AMM 11-32-25 P.Block 001)
5. Close-up
________ Subtask 25-23-47-865-083
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15WN, 13WN, 48WV.
Subtask 25-23-47-410-068
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the related emergency exit door (Ref. TASK 52-22-00-410-001)
(3) Remove the access platform(s). Subtask 25-23-47-862-058
C. De- energize the aircraft electrical circuits. (Ref. TASK 24-42-00-862-001)
TASK 25-23-47-000-009
Removal of the Door Frame Linings of the RH FWD Emergency Exit Door, zone 232
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备2(46)
