(2)
Install the escape slide lever cover (4) with the screws (5), (6) and the washers (7) as identified during the removal procedure.
Subtask 25-23-47-420-063
L. Installation of the End Panel (1)
(Ref. Fig. 401/TASK 25-23-47-991-008)
(1)
Make sure that the work area is clean and clear of tools and other items.
(2)
Put the end panel (1) in position on the structure of the overhead stowage compartment, engage the attach brackets to the yo-yo rolls and install the screw (2) and the washer (3).
Subtask 25-23-47-210-068
M. Visual Inspection
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
If necessary install the new placards, refer to (Ref. TASK 11-00-00-400-002) (Ref. AMM 11-32-25 P.Block 001)
5. Close-up
________ Subtask 25-23-47-865-061
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1WL, 2WL, 3WL, 153RH
Subtask 25-23-47-410-066
B. Close Access
(1)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2)
Close the related emergency exit door (Ref. TASK 52-22-00-410-001).
(3)
Install the cabin emergency light 35WL (Ref. TASK 33-51-11-400-001).
(4)
Install the cabin-wall mounted emergency-exit-marker 90WL3 (Ref. TASK 33-51-13-400-001).
(5)
Install the emergency exit sign 47WL (Ref. TASK 33-51-16-400-001).
(6)
Remove the access platform(s).
Subtask 25-23-47-862-053
C. De-energize the ground service network (Ref. TASK 24-42-00-862-001)
TASK 25-23-47-000-012 Removal of the Door Linings of the LH FWD Emergency Exit Door, zone 231
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 52-22-00-010-001 Opening of the Emergency Exit Doors from the Passenger Compartment 52-73-21-000-003 Removal of the SLIDE ARMED Indicator-Light (2WN1,2WN2,21WN1,21WN2) of the Emergency Exit 52-73-22-000-003 Removal of the CABIN PRESSURE Warning Light Panel (19WN1,19WN2,20WN1,20WN2) of the Emergency Exit 25-23-47-991-014 Fig. 402
3. Job Set-up
__________ Subtask 25-23-47-861-074
A. Aircraft Maintenance Configuration
(1) Energize the ground service network
(Ref. TASK 24-42-00-861-001)
Subtask 25-23-47-010-066
B. Get Access
(1) Put the access platform in position at the related emergency exit(s).
(2) Open the related emergency exit door. (Ref. TASK 52-22-00-010-001) Subtask 25-23-47-865-079
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
4. Procedure
_________
(Ref. Fig. 402/TASK 25-23-47-991-014)
WARNING : BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:
_______
-
THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
-
THE PERCUSSION LEVER OF THE DOOR-DAMPER AND EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
Subtask 25-23-47-020-108
A. Removal of the Door Lining 833JZ (1)
(Ref. Fig. 402/TASK 25-23-47-991-014)
(1) Remove the screws (8), the washers (9) and the door lining (1) Subtask 25-23-47-020-109
B. Removal of the Door Lining 833EZ (7)
(Ref. Fig. 402/TASK 25-23-47-991-014)
(1) Remove the screws (10), the washers (11) and the door lining (7).
Subtask 25-23-47-020-110
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备2(44)
