EFF : ALL
25-28-41Page 402
Feb 01/04
R Textile Floor-Covering (TF) Attached with Dispersions Adhesive R Figure 401/TASK 25-28-41-991-001
EFF : ALL
25-28-41Page 403
Feb 01/04 CES
TASK 25-28-41-400-001
Installation of the Textile Floor-Covering
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific vacuum cleaner
No specific 1 ROLLER - RUBBER
No specific 1 SCRAPER - NON METALLIC
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-002 USA MIL-P-8116 PUTTY, ZINC CHROMATE GENERAL PURPOSE (Ref. 20-31-00) Material No. 08-084 D DAN 490B POLYESTER FILM TAPE (TRANSPARENT) (Ref. 20-31-00)
Material No. 08-102 F AIMS 10-04-005
DISPERSION-ADHESIVE FOR TEXTILE FLOOR COVERING
(Ref. 20-31-00)
Material No. 08-112 D DAN 328
TAPE COTTON FABRICDOUBLE SIDED SELF ADHESIVE
(Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
EFF : ALL
25-28-41Page 404
R C. Expendable Parts
R -------------------------------------------------------------------------------
R FIG.ITEM |DESIGNATION |IPC-CSN
R -------------------------------------------------------------------------------
R 4 Section 25-28-09 03P-050
R D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External
Power
24-42-00-862-001 De-energize the Ground Service Network Supplied from
the External Power
25-21-41-400-001 Installation of the Passenger Seats
25-28-41-991-001 Fig. 401
3. Job Set-up__________
Subtask 25-28-41-860-050
A. Aircraft Maintenance Configuration
(1)
Make sure that the ground service network is energized
(Ref. TASK 24-42-00-861-001).
(2)
Make sure that the TF area is free from equipment and furnishings.
4. Procedure
_________
Subtask 25-28-41-160-050
A. Clean Component Interface and/or Adjacent Area
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
EFF : ALL
25-28-41Page 405
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE_______
R MATERIAL/S.
R USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
R (1) Clean the floor-panel area (1) and the top of the seat-tracks (3)
R with CLEANING AGENTS (Material No. 11-004) and a lint-free cotton
R cloth MISCELLANEOUS (Material No. 19-003).
R (2) If necessary, use a SCRAPER - NON METALLIC to remove the old adhesive
R tape from the floor-panels.
R CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE_______
R MADE OF CARBONFIBER REINFORCED PLASTIC.
R (3) Make sure that the work area is free from dust and other particles.
R If necessary use a vacuum cleaner.
Subtask 25-28-41-210-050
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备2(103)
