(e)
Remove the clamp from the captain's control wheel.
(f)
Turn the captains's control wheel counterclockwise to the stop.
(g)
Install the clamp on the captain's control wheel.
(h)
Turn the first officer's control wheel clockwise to the stop. 1) Make sure the control wheel turns a minimum of 185 degrees. 2) Remove the clamp from the captain's control wheel.
(i)
Move the speed brake handle to full up position.
(j)
Use the clamp to keep the captain's control wheel in the neutral position.
(k)
Install the control wheel adapter on the first officer's control wheel.
NOTE: If the adapter is not available, put a force on the
____ control wheel at a 6.5 inch radius. The torque is equal to the resultant force multiplied by 6.5 inches.
(l)
Attach a torque wrench to the first officer' control wheel adapter.
(m)
Turn the control wheel clockwise to 95 degrees. 1) Make sure the torque is between 299-417 pound-inches. 2) Make sure that spoilers No. 1 and No. 2 are full down.
(n)
Turn the control wheel counterclockwise to 95 degrees. 1) Make sure the torque is between 299-417 pound-inches. 2) Make sure that spoilers No. 11 and 12 are full down.
(o)
Release the clamp on the captain's control wheel.
S 725-099
(2)
Do a test of the control wheel friction and center operation.
(a)
Make sure that the leading edge and trailing edge flaps are fully retracted.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-11-00
ALL ú ú 03 Page 531 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(b)
(c)
(d)
(e)
(f)
(g)
(h)
(i)
A
747-400 MAINTENANCE MANUAL
Make sure the control wheel is in the neutral position.
Operate the trim switch until the trim indicator shows zero
units of trim.
Turn the control wheel clockwise to 1 unit of trim, hold
momentarily, and release.
1) Make sure the control wheel moves back to its neutral
position (use a tolerance of +/- 2 degrees).
NOTE: The trim indicator measures the control wheel
____ position. The control wheel movement of 2 degrees is equal to 0.07 inch measured at the trim indicator scale.
Turn the control wheel counterclockwise to 1 unit of trim, hold momentarily, and release. 1) Make sure the control wheel moves back to its neutral
position (use a tolerance of +/- 2 degrees).Turn the control wheel clockwise to 5 unit of trim, hold momentarily, and release. 1) Make sure the control wheel moves back to its neutral
position (use a tolerance of +/- 2 degrees).Turn the control wheel counterclockwise to 5 unit of trim, hold momentarily, and release. 1) Make sure the control wheel moves back to its neutral
position (use a tolerance of +/- 2 degrees).Remove hydraulic power systems 3 and 4.Set the FLT CONTROL HYD POWER WING switches No. 3 and 4 to SHUTOFF and No. 1 and 2 to NORM. 1) Make sure the control wheel is in the neutral position. 2) Turn the control wheel clockwise to 1 unit of trim, hold
momentarily, and release. a) Make sure the control wheel moves back to its neutral position (use a tolerance of +/- 2 degrees).
3) Turn the control wheel counterclockwise to 1 unit of trim, hold momentarily, and release. a) Make sure the control wheel moves back to its neutral
position (use a tolerance of +/- 2 degrees).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-11-00
ALL ú ú 03 Page 532 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
4) Turn the control wheel clockwise to 5 unit of trim, hold momentarily, and release. a) Make sure the control wheel moves back to its neutral
position (use a tolerance of +/- 2 degrees).
5) Turn the control wheel counterclockwise to 5 unit of trim, hold momentarily, and release. a) Make sure the control wheel moves back to its neutral
position (use a tolerance of +/- 2 degrees).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 1(65)
