(3)
Put the floor panels (1), the section hoses (3), (4), (5) and (6) in position.
NOTE : Refer to the identification made during the removal procedure.
____
(4) Protective treatment. WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(a) Apply SPECIAL MATERIALS (Material No. 05-002) to the screws (2).
(5) Install the screws (2) and if removed the washers (8) and the nuts (9).
NOTE : Refer to the identification made during the removal procedure.
____
(6)
TORQUE the screws (2) to 0.42 m.daN (37.16 lbf.in).
(7)
Position the cord (7) FIBER GLASS CORD 1.1MM DIA. (DAN107-1) in the gap between the floor panels (1).
NOTE : Make sure that the cord (7) comes out at both ends:
____
-
approximatly 100.0 mm (3.9370 in.), between the sloped floor panels (1), and
-
approximatly 200.0 mm (7.8740 in.), between the flat floor panels (1).
(8)
Apply SEALANTS (Material No. 09-005) in the gap between the floor panels (1) and the cutouts of the tiedown positions.
(9)
Make a loop of the cord ends (7) and press into the sealant. NOTE : This will help with the next removal procedure.
____ **ON A/C ALL
5. Close-up
________ Subtask 53-42-14-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Set the AFT CARGO COMPT light switch 8LU to OFF.
(3)
Remove the access platform(s).
(4)
Close the AFT cargo-compartment door (Ref. TASK 52-30-00-860-002).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
EFF : ALL
53-42-14Page 414
FLOOR PANELS - AFT CARGO COMPARTMENT ZONE 160 - REMOVAL/INSTALLATION
____________________________________________________________________
TASK 53-42-17-000-001
Removal of the BULK Cargo-Compartment Floor-Panels
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific nonmetal scraper
No specific access platform 1.8 m (5 ft. 11 in.)
No specific access platform 2 m (6 ft. 7 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 52-30-00-860-006 Open the Bulk Cargo-Compartment Door
R **ON A/C 001-049, 051-099, 101-101, 106-149, 221-221, 224-224, 228-228,
53-42-17-991-001 Fig. 401 R **ON A/C 102-105,
53-42-17-991-001-A Fig. 401A
**ON A/C 151-199,
53-42-17-991-001-C Fig. 401B
EFF : ALL
53-42-17Page 401
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
**ON A/C 201-220, 222-223, 225-227, 229-299,
53-42-17-991-001-B **ON A/C 301-399,
53-42-17-991-001-D R **ON A/C 401-499,
R 53-42-17-991-001-E **ON A/C ALL
3. Job Set-up
__________
Fig. 401C
Fig. 401D
Fig. 401E
**ON A/C 001-049, 051-099, 101-149, 221-221, 224-224, 228-228,
Subtask 53-42-17-010-050
A. Get Access
(1) Put the access platform in position below the BULK cargo-compartment door.
(2) Open the BULK cargo-compartment door (Ref. TASK 52-30-00-860-006). R **ON A/C 151-199, 201-220, 222-223, 225-227, 229-299, 301-399, 401-499,
Subtask 53-42-17-010-050-A
A. Get Access
(1)
Open the AFT cargo-compartment door (Ref. TASK 52-30-00-860-001).
(2)
Put the access platform in position below the AFT cargo-compartment door.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUSELAGE 机身3(82)
