A320飞机维护手册 AMM FUSELAGE 机身3(42)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
 WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
 (1) Clean the area with a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003) and the CLEANING AGENTS (Material No. 11-004), and let the area dry.
 EFF : ALL 53-41-00Page B637

Nov 01/04
R
 CES  4. Procedure

_________
 (Ref. Fig. 650/TASK 53-41-00-991-075) Subtask 53-41-00-210-119
 A. Inspection
 (1) Examine the following area for scratches, dents and cracks:
 -the external fuselage skin around the cutout for the lavatory (waste) service door between FR 65 and FR 66 and from stringer 33 to stringer 40, RH.
 NOTE : If necessary, refer to the ASRM (Ref. ASRM 53-41-11-101) for
____
 the allowable damage limits.

 NOTE : If necessary, refer to the ASRM (Ref. ASRM 53-41-11-201) for
____
 the correct repair procedure.

 5. Close-up
________ Subtask 53-41-00-942-099
 A. Remove the ground support equipment.
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the warning notice(s).

 (3)
 Remove the access platform(s).

 EFF : ALL 53-41-00Page B638

Nov 01/04
R
 CES

 External Fuselage Skin around the Cutout for the Lavatory (Waste) Service Door Figure 650/TASK 53-41-00-991-075
 EFF : ALL 53-41-00Page B639 Nov 01/04 R CES

 TASK 53-41-00-210-818

 General Visual Inspection of Upper Skin of Longitudinal Lap Joints, including Crack Stopper Areas at STGR 41 RH, between FR 51 and FR 58, External Surface
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______ FALL CAN INJURE OR KILL YOU.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 534161-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice No specific 1 ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004  USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
 Material No. 19-003  USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 EFF : ALL  53-41-00Page B640

Nov 01/04
R
 CES

 C. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASRM 53-41-11-101 (for corrective action)
 ASRM 53-41-11-201 (for corrective action)

 **ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
 53-41-00-991-076 Fig. 651 R **ON A/C 151-199, 401-499,
 53-41-00-991-076-A Fig. 651A
 **ON A/C ALL

 3. Job Set-up
__________
 Subtask 53-41-00-941-078

 A. Install the ground support equipment.
 (1)
 Put a warning notice in position to tell persons not to operate the flight controls.

 (2)
 Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in the required position.

 Subtask 53-41-00-110-101
 B. Cleaning Procedure WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUSELAGE 机身3(42)