-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL
_______
MATERIAL.
THIS MATERIAL IS DANGEROUS.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1)
Put the access platform in position below the access door 312AR.
(2)
Open the access door 312AR.
(3)
Get access to the inspection area.
(4)
Carefully clean the inspection area with CLEANING AGENTS (Material No. 11-002) and a lint-free cloth.
EFF : ALL
53-51-00Page 639
Aug 01/04
R
CES
4. Procedure
_________
(Ref. Fig. 610/TASK 53-51-00-991-012)
Subtask 53-51-00-210-065
A. Inspection:
(1) Examine the THS actuator attach fittings for:
-cracks,
-loose or missing rivets,
-distortion.
NOTE : For additional information of the attach fittings (Ref. ASRM
____
535129)
5. Close-up
________
Subtask 53-51-00-916-055
A. Apply STORAGE PRESERVATION (Material No. 15-005) to the inspection area, if you have removed the surface protection (Ref. TASK 51-75-13-916-001).
Subtask 53-51-00-410-065
B. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
R (2) Close the access door 312AR.
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
EFF : ALL
53-51-00Page 640
THS Actuator Attachment Fittings
Figure 610/TASK 53-51-00-991-012
EFF : ALL 53-51-00 Page 641
Feb 01/98
CES
TASK 53-51-00-210-012
Detailed Visual Inspection of Fin to Fuselage FWD, MID and AFT Attach Fittings, Outside Fuselage, LH/RH
1. Reason for the Job
__________________
Refer to the MPD TASK: 535162-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific lint-free cloth
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00) Material No. 15-005 AIB TN 10138 TYPE I GRADE 2
CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND
(Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
51-75-13-916-001 Repair to a layer of Moisture-Removing Oil 53-55-11-000-001 Removal of the Fairings 323AL/323AR 53-55-11-400-001 Installation of the Fairings 323AL/323AR ASRM 535500000 (for corrective action) 53-51-00-991-006 Fig. 611
EFF : ALL
53-51-00Page 642
3. Job Set-up
__________
Subtask 53-51-00-010-059
A. Get Access
R WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION_______
R BEFORE YOU START A TASK ON OR NEAR:
R - THE FLIGHT CONTROLS
R - THE FLIGHT CONTROL SURFACES
R - THE LANDING GEAR AND THE RELATED DOORS
R - COMPONENTS THAT MOVE.
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL_______
R MATERIAL.
R THIS MATERIAL IS DANGEROUS.
R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______
R MATERIALS ONLY WITH A GOOD SUPPLY OF AIR.
R OBEY THE MANUFACTURERS INSTRUCTIONS.
R PUT ON PROTECTIVE CLOTHING.
R DO NOT GET THEM IN YOUR MOUTH.
R DO NOT SMOKE.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUSELAGE 机身3(108)
