Nov 01/04
R
CES -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
51-75-12-300-001 Repair of Major Paint Damage on Light Alloy and
Composite Material 51-75-12-300-003 Repair of Minor Paint Damage (Topcoat Only) ASRM 51-11-00-001 ASRM 51-22-00-001 NTM 534106-Part.4 ASRM 51-73-00-001 (for corrective action) ASRM 51-74-00-001 (for corrective action) ASRM 53-00-12-201 (for corrective action) 53-41-00-991-013 Fig. 610
3. Job Set-up
__________
Subtask 53-41-00-010-085
A. Get Access
(1)
Remove the right upper sidewall panels 252PW, 252LW, 252HW (Ref. TASK 25-23-43-000-001) and the right lower sidewall panels 252NW, 252KW (Ref. TASK 25-23-44-000-001).
(2)
Remove the insulation blankets from the inspection area (Ref. TASK 25-80-00-000-001).
NOTE : Identify the insulation blankets for installation.
____
(3) If necessary, remove the air distribution riser-ducts to get access to the inspection areas at FR54 and FR56 (Ref. TASK 21-20-00-010-001).
Subtask 53-41-00-860-053
B. Preparation of the Inspection Areas
(Ref. Fig. 610/TASK 53-41-00-991-013)
(1) Make sure that the surfaces of the inspection areas are clean and smooth.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
EFF : ALL 53-41-00Page B693
Nov 01/04
R
CES WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(2)
If necessary, clean the inspection areas with the CLEANING AGENTS (Material No. 11-004) and a MISCELLANEOUS (Material No. 19-003). Make sure the inspection areas are dry before you continue.
(3)
If necessary, make the surface of the inspection areas smooth with the abrasive cloth, grade 280.
(4)
Do a visual inspection of the inspection areas. Look for damage and defects in the shape of the external surface.
(5)
If you find damage :
(a)
Refer to the ASRM (Ref. ASRM 51-11-00-001) for the classification of the damage.
(b)
If you find corrosion damage:
-
refer to the ASRM (Ref. ASRM 51-22-00-001) for the general corrosion data
-
refer to the ASRM (Ref. ASRM 51-74-00-001) for the repair of the corroded areas.
(c)
If you find other types of damage:
-Refer to the ASRM (Ref. ASRM 51-73-00-001) for the repair of the minor damage.
EFF : ALL 53-41-00Page B694
Nov 01/04
R
CES 4. Procedure
_________ (Ref. Fig. 610/TASK 53-41-00-991-013) Subtask 53-41-00-220-052
A. Special Detailed Inspection Procedure
(1)
Do the special detailed inspection of the frame splices at FR53 thru FR56, above the STGR18 RH (Ref. NTM 534106-Part.4).
(2)
Write a report if you find damage during the inspection procedure.
(3)
If you find damage:
(a)
Refer to the ASRM (Ref. ASRM 51-11-00-001) for the classification of the damage.
(b)
If you find corrosion damage:
-
refer to the ASRM (Ref. ASRM 51-22-00-001) for the general corrosion data
-
refer to the ASRM (Ref. ASRM 51-74-00-001) for the repair of the corroded areas.
(c)
If you find other types of damage:
-
refer to the ASRM (Ref. ASRM 51-73-00-001) for the repair of the minor damage
-
refer to the ASRM (Ref. ASRM 53-00-12-201) for the correct repair procedure.
中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM FUSELAGE 机身3(54)
