(b)
If you find corrosion damage:
-
refer to the ASRM (Ref. ASRM 51-22-00-001) for the general corrosion data
-
refer to the ASRM (Ref. ASRM 51-74-00-001) for the repair of the corroded areas.
(c)
If you find other types of damage:
-Refer to the ASRM (Ref. ASRM 51-73-00-001) for the repair of the minor damage.
EFF : ALL 53-41-00Page C633
Nov 01/04
R
CES 4. Procedure
_________
(Ref. Fig. 661/TASK 53-41-00-991-048)
Subtask 53-41-00-220-059
A. Special Detailed Inspection Procedure
(1) Do the special detailed inspection of the aft cargo door lock fittings, and the surrounding structure. Do this from STGR41 RH to the internal part of the door sill, at 6 places (Ref. NTM 534156-Part.6).
NOTE : If the inspection areas are painted , before you do the
____
inspection you must:
-refer to the procedure steps in the NTM (Ref. NTM 534156-Part.6), 'Preparation for Inspection'
-measure the thickness of the paint at the inspection areas
-make sure that the paint thickness is less than the given limit.
(2)
Write a report about the damage you find during the inspection procedure.
(3)
If you find damage:
(a)
Refer to the ASRM (Ref. ASRM 51-11-00-001) for the classification of the damage.
(b)
If you find corrosion damage:
-
refer to the ASRM (Ref. ASRM 51-22-00-001) for the general corrosion data
-
refer to the ASRM (Ref. ASRM 51-74-00-001) for the repair of the corroded areas.
(c)
If you find other types of damage:
-
refer to the ASRM (Ref. ASRM 51-73-00-001) for the repair of the minor damage.
-
refer to the ASRM (Ref. ASRM 53-46-11-101) for the allowable damage data for the latch fittings.
5. Close-up
________
Subtask 53-41-00-370-058
A. Repair of the Surface Protection
(1) If necessary, repair the paint coatings in the inspection areas (Ref. TASK 51-75-12-300-003) or (Ref. TASK 51-75-12-300-001).
**ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
Subtask 53-41-00-410-121
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the insulation blankets (Ref. TASK 25-80-00-400-001).
(3)
Install the AFT cargo-compartment floor-panels 151DF and 151GF (Ref. TASK 53-42-14-400-001).
(4)
If removed, install the rear additional center tank (Ref. AMM 28-11-27, Page Block 401).
(5)
Close the AFT cargo-compartment door (Ref. TASK 52-30-00-860-002).
(6)
Remove the access platform(s).
(7)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R **ON A/C 151-199, 401-499,
Subtask 53-41-00-410-121-A
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the insulation blankets (Ref. TASK 25-80-00-400-001).
(3)
Install the AFT cargo-compartment floor-panels 151VG and 151ZG (Ref. TASK 53-42-14-400-001).
(4)
If removed, install the rear additional center tank (Ref. AMM 28-11-27, Page Block 401).
(5)
Close the AFT cargo-compartment door (Ref. TASK 52-30-00-860-002).
(6)
Remove the access platform(s).
(7)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
**ON A/C 301-399,
TASK 53-41-00-220-012
Special Detailed Inspection of Splice Plate at Circumferential Skin Splice at FR47.5 from Stringer 16 LH and RH to Crown Center Line, External
1. Reason for the Job
__________________
Refer to the MPD TASK: 534145-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
No specific access platform 5.5 m (18 ft. 1 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUSELAGE 机身3(65)
